Control a Radio PLL with a PIC

[Archangel]

Do you have an old Knight Kit radio as well?
Display channels or frequency? This sounds great. How would I do that?
My displays are only 3 digits.

Nope no Knight kit, I was thinking of a retrofit for old 23 ch CB radios make them useful, other freqs, 10M . . . set a couple of vars

 temp var byte

 i var byte

 lookup i[010,020,030 . . .500],temp

this aliases your count to the numbers in the lookup table . . . You could set a freq switch with static displays like 142, 143, 144 . . . and follow with the displays driven by the lookup table displaying the fine freqs. Or change up to a word var and you have up to 65535 values you could step through, or use 2 encoders (old Henry 2m used 2 switches ganged) sorry about the code formats, crazy forum software glitch killed formatting for me, so I had to do it this way.

[RayL113]

Var, I take to mean variable. Remember I'm new to Pics and PBP. So a word var? Is this an extended table?

[mackrackit]

From the manual

4.3. Variables

Variables are where temporary data is stored in a PICBASIC PRO™ program. They are created using the VAR keyword. Variables may be bits, bytes or words. Space for each variable is automatically allocated in the microcontroller=s RAM by PBP. The format for creating a variable is as follows:

There are basically four sizes a VAR can be while using PicBasicPro 2.6x
BIT = number of BITs - 1
BYTE = number of BITs - 8
WORD = number of BITs -16
LONG = number of BITs - 32

[Archangel]

Yes, var= variable
bit is one of the placeholders in the larger variable, example
say you want a variable to hold a value as a flag for an event, you could make a bit variable, called . . . FLAGBIT this way FLAGBIT VAR BIT
or you might need several flag bits and do it this way
FLAGBIT VAR BYTE which gives you an 8 bit byte full of FLAGBITS as follows
FLAGBIT.0 lowest bit in the byte
FLAGBIT.1 second bit in the byte
FLAGBIT.2 third " " " "
FLAGBIT.3 . . .
FLAGBIT.4 . . . all the way to FLAGBIT.7 , FLAGBIT.7 being the highest order bit in the byte variable
which is to say you can address every bit of your variable individually.
Byte = %00000000 will hold 0 to 255 in decimal
word = %00000000 00000000 will hold 0 to 65535 in decimal
LONG = %00000000 00000000 00000000 00000000 which is 4294967295 but I think (I am not sure of this) only allows 1/2 that much on each side of zero -2147483647 0 2147483647

Notice the way I have written the binary expression %00000000 this is the appropriate syntax for P Basic Pro, other compilers may use different "punctuation" and you will see "BIG ENDIAN" and LITTLE ENDIAN" usage and all that means is which end of the group of zeros is the least significant bit, the Left or the Right.

You will see different ways of displaying hex as well, in PBP we use $00 whereas in C you might see something like 0h00

[mister_e]

in PBP we use $00 whereas in C you might see something like 0h00

high likely 0x00

[ScaleRobotics]

This may not be it, but the only thing I notice is: you have OSC_HS selected, but you are using an oscillator at 4 mhz. If you are using an oscillator instead of a resonator, this should be set to XT for 4 mhz. If you are using a resonator, did you see the note with the data sheet?

Note: When using resonators with frequencies
above 3.5 MHz, the use of HS mode,
rather than XT mode, is recommended.
HS mode may be used at any VDD for
which the controller is rated. If HS is
selected, it is possible that the gain of the
oscillator will overdrive the resonator.
Therefore, a series resistor should be
placed between the OSC2 pin and the
resonator. As a good starting point, the
recommended value of RS is 330Ω.

[Dave]

Rayl113, Also make sure the "PBADEN" bit's are set for Digital on reset. Other wise the port Bb.0 thru B.3 are set as analog after reset....

[RayL113]

Yes, var= variable
bit is one of the placeholders in the larger variable, example
say you want a variable to hold a value as a flag for an event, you could make a bit variable, called . . . FLAGBIT this way FLAGBIT VAR BIT
or you might need several flag bits and do it this way
FLAGBIT VAR BYTE which gives you an 8 bit byte full of FLAGBITS as follows
FLAGBIT.0 lowest bit in the byte
FLAGBIT.1 second bit in the byte
FLAGBIT.2 third " " " "
FLAGBIT.3 . . .
FLAGBIT.4 . . . all the way to FLAGBIT.7 , FLAGBIT.7 being the highest order bit in the byte variable
which is to say you can address every bit of your variable individually.
Byte = %00000000 will hold 0 to 255 in decimal
word = %00000000 00000000 will hold 0 to 65535 in decimal
LONG = %00000000 00000000 00000000 00000000 which is 4294967295 but I think (I am not sure of this) only allows 1/2 that much on each side of zero -2147483647 0 2147483647

Notice the way I have written the binary expression %00000000 this is the appropriate syntax for P Basic Pro, other compilers may use different "punctuation" and you will see "BIG ENDIAN" and LITTLE ENDIAN" usage and all that means is which end of the group of zeros is the least significant bit, the Left or the Right.

You will see different ways of displaying hex as well, in PBP we use $00 whereas in C you might see something like 0h00

Thanks that helps alot. Yes I had noticed the % in front of what looked like binary expressions but hadn't noticed the $ in front of hex expressions. Can you still use the "b and h" in PCB? In case I forget and use the asm expression?

[mackrackit]

Can you still use the "b and h" in PCB?

Nope.
From the manual.
4.8. Numeric Constants

PBP allows numeric constants to be defined in the three bases: decimal, binary and hexadecimal. Binary values are defined using the prefix '%' and hexadecimal values using the prefix '$'. Decimal values are the default and require no prefix.

100 ' Decimal value 100
%100 ' Binary value for decimal 4
$100 ' Hexadecimal value for decimal 256

[RayL113]

What if I want to use a cb channel switch instead of an encoder? The first four pins have a logical progression of 0000 to 1111. Couldn't I use this like a Gray code encoder? Count increase would equal up and count decrease would equal down. What do you think?

[cncmachineguy]

You can use that, you can use the thing you already have, its up to you. They both CAN work. With the CB switch you will only get 16 changes per full revolution. If this is enough then use it. It will prolly still have noisey output so de-bouncing will still be neccessary. Now if you can get this, I have used many, they work really well.

Let us know how you are getting along on this project. Have you blinked a LED on port A yet?