sinusoidal pwm

[bwaxing]

hellow,
i'm trying to simulate this code on proteus isis but m getting nothing meaningful.My code compile succesfully...i need help..please

define OSC 20

;*****************VARIABLE DECLARATION******************************************
wsave   VAR BYTE    $70     SYSTEM      ' alternate save location for W 
wsave1  VAR BYTE    $A0     SYSTEM      ' location for W if in bank1
wsave2  VAR BYTE    $120    SYSTEM      ' location for W if in bank2
wsave3  VAR BYTE    $1A0    SYSTEM      ' location for W if in bank3
STEPCOUNT var byte                      'Define stepcount as byte type variable
stepcount = 256

;**************SETTING THE REGISTERS WITH APPROPIATE BIT DEFINITION************* 
ADCON0 = %00000000
ADCON1 = %00000000  ;all anolog output
trisb = %11111111   ;define porta as input
trisc = %11111011   ;make ccp1/portc.2 an output pin
trisa = %11111111   ;define porta as input
TMR2 = 16
PR2 = 34           ;set for 36Khz HPWM(=72 steps*10 times*50hz)        
CCP1CON = %000001100       ;set to pwm mode
T2CON=%00000110           ;enable timer2 and set timer2 prescaler value of 1:4

;****************A sine lookup table in an array********************************
sineval var byte[72]
sineval[1] = 128      ;0 degree
sineval[2] = 137      ;5 degree
sineval[3] = 146
sineval[4] = 154
sineval[5] = 163
sineval[6] = 171
sineval[7] = 179
sineval[8] = 187
sineval[9] = 194
sineval[10] = 200
sineval[11] = 206
sineval[12] = 212
sineval[13] = 216
sineval[14] = 220
sineval[15] = 224
sineval[16] = 227
sineval[17] = 228
sineval[18] = 229
sineval[19] = 230     ;90 degree
sineval[20] = 229
sineval[21] = 228
sineval[22] = 227
sineval[23] = 224
sineval[24] = 220
sineval[25] = 216
sineval[26] = 212
sineval[27] = 206
sineval[28] = 200
sineval[29] = 194
sineval[30] = 187
sineval[31] = 179
sineval[32] = 171
sineval[33] = 163
sineval[34] = 154
sineval[35] = 146
sineval[36] = 137
sineval[37] = 128  ;180 degree
sineval[38] = 119
sineval[39] = 110
sineval[40] = 102
sineval[41] = 93
sineval[42] = 85
sineval[43] = 77
sineval[44] = 69
sineval[45] = 62
sineval[46] = 56
sineval[47] = 50
sineval[48] = 44
sineval[49] = 40
sineval[50] = 36
sineval[51] = 32
sineval[52] = 29
sineval[53] = 28
sineval[54] = 26
sineval[55] = 26
sineval[56] = 26
sineval[57] = 28
sineval[58] = 29
sineval[59] = 32
sineval[60] = 36
sineval[61] = 40
sineval[62] = 44
sineval[63] = 50
sineval[64] = 56
sineval[65] = 62
sineval[66] = 69
sineval[67] = 77
sineval[68] = 85
sineval[69] = 93
sineval[70] = 102
sineval[71] = 110
sineval[72] =119
 
timerone var word 
 
INCLUDE "DT_INTS-14.bas"     ; Base Interrupt System

;********Define INT_Handler as ISR********************************************** 
ASM
 
INT_LIST  macro    ; IntSource,        Label,  Type, ResetFlag?
        INT_Handler   TMR1_INT,   _sine,   ASM,  yes
    endm
    INT_CREATE               ; Creates the interrupt processor
ENDASM

T1CON = $31    ; Prescaler = 8, TMR1ON          
TMR1L = 255    
TMR1H = 254
@   INT_ENABLE  TMR1_INT     ; Enable Timer 1 Interrupts  
timerone = $FA93               ;gives about 50 hz sine 
Main:
        pause 5
        'if timerone = $F9FF then timerone = $FF00
 
GOTO Main
 
'---[TMR1_INT - interrupt handler]------------------------------------------
 
sine:
    TMR1L = timerone.byte0
    TMR1H = timerone.byte1     
    CCPR1L = sineval[STEPCOUNT]>>1 
    stepcount = stepcount -1
    if stepcount = 0 then stepcount = 72
@    INT_RETURN

attached is the circuit and the simulation result done on proteus isis