16F1824 "HPWM 2" woes (command seemingly forces PortC.3 from analogue to digital)

[HankMcSpank]

Hank, I am fairly certain you can't use the pin for PWM output and Analog input at the same time. Your work around is not a work around at all. It is multiplexing the pin for both functions.

There are both on C.3 - Yes?

Hi Bert.....you see how a fresh pair of eyes helps? :-) now as it goes, I'm not using the same pin for both functions...

16f1824 Pin 7 (portC.3) is CCP2 (I'm assuming that the Picbasic command "HPWM 2" uses CCP2?)

16f1824 Pin 9 (PortC.1) is my ADC input pin ...but I can see that that's been set wrong in my code cut/paste above (that pasted code was a quick rip/strip from my monster main program, and there's likely been an error as I've also been rejigging pins to make for a better PCB layout!)

correction made to my code in bold below....

@ __CONFIG _CONFIG1, _FCMEN_OFF & _FOSC_INTOSC & _WDTE_OFF & _MCLRE_OFF & _CP_OFF & _IESO_OFF & _BOREN_OFF & _PWRTE_OFF & _LVP_OFF
@ __CONFIG _CONFIG2, _LVP_OFF

DEFINE  OSC 4   

Osccon = %01101010   'sets the internal oscillator to 4Mhz

DEFINE DEBUG_BAUD 9600
DEFINE DEBUG_MODE 2
DEFINE DEBUG_REG PORTC
DEFINE DEBUG_BIT 4

DEFINE ADC_BITS  8     ' ADCIN resolution  (Bits)
DEFINE ADC_CLOCK 1     ' ADC clock source  (Fosc/8)
DEFINE ADC_SAMPLEUS 11 ' ADC sampling time (uSec)

ADCON0 = %00010101    'AN5 (Pin 9) Enabled for BACKGROUND ADC'ing VIA SPECIAL EVENT TRIGGER  + ADC On
ADCON1 = %01000011     'set ADC +ve ref to be the internal Fixed VREF   
FVRCON = %11000010     'turn fixed voltage reference on & set it to 2.048V (last two bits set the voltage ...01 =1.024V,10=2.048


CM1CON0 = 0   ' COMPARATORS OFF
CM1CON1 =0
CM2CON0 = 0   ' COMPARATORS OFF
CM2CON1 =0    
CPSCON0 = 0   'CAPACTIVE SENSE MODULE OFF
RCSTA.7 = 0   'SERIAL PORT OFF

TRISA =  %11111111
TRISC =  %11110101     ' PIN 7 RC3 HPWM  OUTPUT
ANSELA = 0
ANSELC = %00000010      ' AN5 Pin9 (PortC.1) ADC input ....BACKGROUND ADC'ing VIA CCP4 SPECIAL EVENT TRIGGER  
CCP2CON    = %00001100    'NOT ENTIRELY CONFIDENT ABOUT THIS ONE!

Sig_In          VAR BYTE  ; a variable to store to DC level coming in on pin 19 (RA0)
duty            var word
latest_sample   var word

'setup the AtoD & special event register to capture samples in the background
T1CON = %00000001         ' timer1 on
CCP4CON = %0001011     'set CCP4 to special event trigger.

CCPR4H = 0         ' preset for timer1 match (MSB register)
CCPR4L = 250       '  @16Mhz, 200 gives 20,000khz sample & 250 gives 16khz sample.

duty = 255
HPWM 2, duty, 32767
TRISC.1 =1   'Remake PIN 9 PortC.1 an input again following HPWM command

TEST: 
latest_sample = ADRESH
PAUSE 500
debug dec LATEST_SAMPLE,13,10
GOTO TEST

....still the same though, when the "HPWM 2" line is reached, my ADC doesn't read properly. I have to reset PortC.1 back to an input, so it looks like the "HPWM 2" command is turning PortC.1 into an output....which for the life of me, I can't understand why that would happen?

Now there'a lot of features in this new(ish) PIC and it's likely something I'm not grasping or seeing, but like I say...way too many hours trying to nail this one.......I now need all the help I can get!

[mtripoli]

Never mind...

[HankMcSpank]

Well, for all my quick 'n dirty the workaround reverts my pin9 (PortC.1) ADC back to how it should be...

HPWM 2, duty, 32767
TRISC.1 =1   'Remake PIN 9 PortC.1 an input again following HPWM command

....the actual HPWM command itself is still playing havoc with the signal....when I feed a steady sine wave into the ADC pin, it getting chopped up as viewed on a scope, as when the HPWM 2 command runs it interferes with PortC.1 - my now (naive) thinking is that it's forcing the pin to be an output, which then drags my sine wave analogue input signal down to zero, then my 'kludgey' follow on command makes the pin an input again...which restores the signal. But you can imagine the end result, it's as if a switch is being flicked rapidly thereby shunting the signal to ground .....fugly.

i'm exhausted on this one & don't have an immediate good solution...I need to sleep on it (still a high possibility I'm just doing something wrong as my head is fuzzy now!). Tomorrow, I may sit down & work out how do do HPWM longhand using the PICs registers (one whole days lost on something as simple as this....eek!)

[Bruce]

DEFINE CCP2_REG PORTC
DEFINE CCP2_BIT 3

Should take care of it. PBP defaults to PORTC.1 for CCP2 if you don't tell it otherwise.

[HankMcSpank]

Thanks Bruce ...that did it....you've just made an impossibly bad day...just bad now

Like I say it's my first time using the 2nd HPWM channel ....but also my first time using this newish PIC in anger - thought i was going crazy.

PWM, SHmeeWM.....

[Ioannis]

These new 16F18xx chips are small in the eye but really beasts!

I had my difficult time in setting them too, but nowI really like them.

Here is my setup for the 1827 which may help others to take into accoun the registers and not forget any of them.

Of course this is my setup and other need to make their own. It just as an example.

  TRISB = %11000101
  TRISA = %11111100
  
  ADCON0 = %00000001
  ADCON1 = %11110011

  ANSELA = %00011100           ' all digital. A/D disabled
  ANSELB = %01000000
  
  APFCON0 = %00100000
  APFCON1 = %00000001
    
  BAUDCON = %00011000
  
  CCP1CON = %00111100          'Control of CCPx modules
  CCP2CON = %00000000
  CCP3CON = %00000000
  CCP4CON = %00000000

  CM1CON0.7=0
  CM2CON0.7=0
  
  CPSCON0 = 0
  CPSCON1 = 0 
  
  DACCON0 = 0
  
  FVRCON = %10000011
  
  INTCON = %11000000   ' global & peripheral ints enabled
  
  OPTION_REG = %10000111    'Tmr0 from 256 presc and Int Clock
  
  PIR1 = 0             ' clear TMR1 int flag                     
  PIE1 = %00000001     ' TMR1 int enabled
  
  T1CON = %00110000    ' TMR1 1:8 prescale, timer1 on
  
  WPUB=%11000000
  
  'hpwm 1,0,2000
  DEFINE CCP1_REG PORTB
  DEFINE CCP1_BIT 3    
  ccptmrs=0
  pr2=249
  ccp1con=$0C

HTH,

Ioannis

[HankMcSpank]

I concur...the 16F182x are a great range of chips...absolutely chocka with features.

I can't say I've had a lot of setup problems with them (certainly nothing that wasn't obvious when I complied)....other than this pesky HPWM 2 issue, the one other issue I had Darrel kindly helped sort....

I needed to modify the 16F1824.INC file (mods in red)....

;****************************************************************
;*  16F1824.INC                                                 *
;*                                                              *
;*  By        : Leonard Zerman, Jeff Schmoyer                   *
;*  Notice    : Copyright (c) 2010 microEngineering Labs, Inc.  *
;*              All Rights Reserved                             *
;*  Date      : 09/14/10                                        *
;*  Version   : 2.60b                                           *
;*  Notes     :                                                 *
;****************************************************************
        NOLIST
    ifdef PM_USED
        LIST
        "Error: PM does not support this device.  Use MPASM."
        NOLIST
    else
        LIST
        LIST p = 16F1824, r = dec, w = -302
        INCLUDE "P16F1824.INC"	; MPASM  Header
        ;__config _CONFIG1, _FOSC_HS
        ;__config _CONFIG2, _PLLEN_OFF & _LVP_OFF
        NOLIST
    endif
        LIST
BLOCK_SIZE	EQU	32
CCPTMRS0 = CCPTMRS

The first two mods (semi colons) are standard fayre, but that last one would have taken me a good few years to get to the bottom of on my own.