A Defines Request

[Kirk Fraser]

Bob,

Thanks, I've added 1K gate resistors and replaced the coils with LED's for testing which should save some parts from burnout. The diodes are electrically connected according to your description, just not near the coils.

Back to learning how to set up the PWM command.

Kirk

[BobP]

Hi Kirk,

If you can use bulbs you will see the PWM better. Let us know how you get on?

Bob

[Kirk Fraser]

I put in the program revision below but again nothing happened. Since all my stuff is already posted earlier, I thought just discussing this section would be most efficient. Any discussion on content or how I can learn to improve the content is welcome. Thanks.

'*** Start of help request ***
DEFINE OSC 48
@ __CONFIG _CONFIG1L, _PLLDIV_1_1L & _CPUDIV_OSC1_PLL2_1L & _USBDIV_2_1L
@ __CONFIG _CONFIG1H, _FOSC_HSPLL_HS_1H
@ __CONFIG _CONFIG2H, _WDT_OFF_2H & _WDTPS_512_2H
@ __CONFIG _CONFIG2L, _PWRT_ON_2L & _VREGEN_ON_2L
@ __CONFIG _CONFIG3H, _PBADEN_OFF_3H & _MCLRE_OFF_3H
@ __CONFIG _CONFIG4L, _LVP_OFF_4L & _XINST_OFF_4L
ADCON0 = 3 ' Setup PortA.0 for A/D function
OSCCON = %01110000
'*** End of help request ***

[Kirk Fraser]

Has anyone gotten the and RCTIME and PWM commands to work? I looked at a C18 program and it looks like one may have to do so much low-level progamming that I wonder if there's more that PB doesn't do besides the config bits.

Here's my latest failure:

DEFINE OSC 48
@ __CONFIG _CONFIG1L, _PLLDIV_12_1L & _CPUDIV_OSC4_PLL6_1L & _USBDIV_2_1L
@ __CONFIG _CONFIG1H, _FOSC_HSPLL_HS_1H & _FCMEM_OFF_1H & _IESO_OFF_1H
@ __CONFIG _CONFIG2L, _VREGEN_ON_2L & _PWRT_OFF_2L & _BOR_OFF_2L & _BORV_28_2L
@ __CONFIG _CONFIG2H, _WDT_OFF_2H & _WDTPS_32768_2H
@ __CONFIG _CONFIG3H, _MCLRE_ON_3H & _LPT1OSC_OFF_3H & _PBADEN_ON_3H & _CCP2MX_ON_3H
@ __CONFIG _CONFIG4L, _STVREN_ON_4L & _LVP_OFF_4L & _ICPRT_OFF_4L & _XINST_OFF_4L
@ __CONFIG _CONFIG5L, _CP0_OFF_5L & _CP1_OFF_5L & _CP2_OFF_5L & _CP3_OFF_5L
@ __CONFIG _CONFIG5H, _CPB_OFF_5H & _CPD_OFF_5H
@ __CONFIG _CONFIG6L, _WRT0_OFF_6L & _WRT1_OFF_6L & _WRT2_OFF_6L & _WRT3_OFF_6L
@ __CONFIG _CONFIG6H, _WRTB_OFF_6H & _WRTC_OFF_6H & _WRTD_OFF_6H
@ __CONFIG _CONFIG7L, _EBTR0_OFF_7L & _EBTR1_OFF_7L & _EBTR2_OFF_7L & _EBTR3_OFF_7L
@ __CONFIG _CONFIG7H, _EBTRB_OFF_7H

I checked the bit configuration above with the PIC18F4550 part of the PIC18 Configuration Settings Addendum, so the above is at least legal syntax, even though I don't know what most of it means. Then I checked the above with the bits which worked to get LED's to flash. I discovered a few differences.

DEFINE OSC 8
@ __CONFIG _CONFIG1L, _PLLDIV_5_1L & _CPUDIV_OSC1_PLL2_1L & _USBDIV_2_1L
@ __CONFIG _CONFIG1H, _FOSC_INTOSCIO_EC_1H
@ __CONFIG _CONFIG2H, _WDT_ON_2H & _WDTPS_512_2H
@ __CONFIG _CONFIG3H, _PBADEN_OFF_3H & _MCLRE_OFF_3H
@ __CONFIG _CONFIG4L, _LVP_OFF_4L & _ICPRT_OFF_4L &_XINST_OFF_4L
OSCCON = %01110000

Some bits are identical, some are set opposite or differently, and some are new while many are ignored in the working application. So I started looking up the differences in the data sheet and found deeper layers which I don't understand. Apparently each group of pins has its own set of potential configurations. I don't even know how to write things from the pin layer based on the table in the data sheet for example in chapter 10.0 I/O PORTS starting on page 113 of the PIC18F4550 data sheet, tables 10-1 and 10-2.

Is there an example of how to set up the bits so a program like mine, posted above, with RCTIME and PWM commands, to make the program work? Thank you.