serial coms - again

[malc-c]

Need one final bit of assistance. We've made the changes to the PC application so that it sends the complete string back to the PIC. Q tells the PIC to send data, S tells it to expect data

QS350635250249250250250249250250250249000000000000000000000000000000001501501501500000000000000000Q

This should then populate the variables as follows

[dec3 normtemp[0]]
[dec3 normtemp[1]]
[dec3 normtemp[2]]
[dec3 normtemp[3]]

[dec3 alarmlow[0]]
[dec3 alarmlow[1]]
[dec3 alarmlow[2]]
[dec3 alarmlow[3]]

[dec3 alarmhigh[0]]
[dec3 alarmhigh[1]]
[dec3 alarmhigh[2]]
[dec3 alarmhigh[3]]

[#StartHour[0] DIG 1,#StartHour[0] DIG 0,#StartMin[0] DIG 1,#StartMin[0] DIG 0]
[#StartHour[1] DIG 1,#StartHour[1] DIG 0,#StartMin[1] DIG 1,#StartMin[1] DIG 0]
[#StartHour[2] DIG 1,#StartHour[2] DIG 0,#StartMin[2] DIG 1,#StartMin[2] DIG 0]
[#StartHour[3] DIG 1,#StartHour[3] DIG 0,#StartMin[3] DIG 1,#StartMin[3] DIG 0]

[#StopHour[0] DIG 1,#StopHour[0] DIG 0,#StopMin[0] DIG 1,#StopMin[0] DIG 0]
[#StopHour[1] DIG 1,#StopHour[1] DIG 0,#StopMin[1] DIG 1,#StopMin[1] DIG 0]
[#StopHour[2] DIG 1,#StopHour[2] DIG 0,#StopMin[2] DIG 1,#StopMin[2] DIG 0]
[#StopHour[3] DIG 1,#StopHour[3] DIG 0,#StopMin[3] DIG 1,#StopMin[3] DIG 0]

[dec3 Droptemp[0]]
[dec3 Droptemp[1]]
[dec3 Droptemp[2]]
[dec3 Droptemp[3]]

[#lightsetHR[0] DIG 1,#lightsetHR[0] DIG 0,#lightsetMN[0] DIG 1,#lightsetMN[0] DIG 0]
[#lightsetHR[1] DIG 1,#lightsetHR[1] DIG 0,#lightsetMN[1] DIG 1,#lightsetMN[1] DIG 0]

[#lightoffHR[0] DIG 1,#lightoffHR[0] DIG 0,#lightoffMN[0] DIG 1,#lightOFFMN[0] DIG 0]
[#lightoffHR[1] DIG 1,#lightoffHR[1] DIG 0,#lightoffMN[1] DIG 1,#lightOFFMN[1] DIG 0]

Now I've used the following to handle the import of things like normtemp etc and that work fine

   TempWD = 0
    HSERIN 1000,RX_Bombed,[DEC3 TempWD]
    normtemp[0] = TempWD   
    SetPoints(0)=normtemp[0]

However I'm having issues formatting the HSERIN sections for the times such as lightsON and Lights OFF and StartHour etc, especially as these are just two digits 00 - 23 for hours and 00 - 59 for mins. MCS reports

Expected ']'

but it doesn't hell me where, and adding them to most logical places (like at the end) still results in similar errors

Any ideas ?