Give it a try, and if you get stuck, post the code you have written here and we can help.Originally Posted by HankMcSpank
|
Give it a try, and if you get stuck, post the code you have written here and we can help.
"I think fish is nice, but then I think that rain is wet, so who am I to judge?" - Douglas Adams
|
chords
3 buttons right? 4 modes.....
press button 1 to enter mode 1
press button 2 to enter mode 2
press button 3 to enter mode 3
press both 1&2 to enter mode 4
press both 2&3 to enter mode 5
|
What if the accuracy wasn't as difficult?
Maybe any 2 buttons pressed at/near the same time could be mode 4.
You wouldn't have to find the correct 2 buttons. Any two (or 3) will do. So it should be easier for the player.
DT
|
Three pins will easily support up to six Charlieplexed switches (requires one diode per switch).
|
Just an update (since you've all been so kind to chime in with your ideas...many thanks!)
Last night got home & thought ok....ok, so let's learn about timers - so I went to Darrel's site & saw the timer based flashing LED example....absolutely perfect for one of my other needs -so I went off on a slight (but related) tangent!!
I have a tri-colour LED - ie a green & red LED (which obviously also gives amber if they're both switched on at the same time).....so three possible colours. But with four operational modes, I also need a visual representation to the player when in the the fouth mode - that'd be a flashing LED!
Previously, I was checking regularly within the main code to see if the player had selected the 4th mode - and if so, I'd flash an led. But as Darrel has mentioned to on his site, it's tricky using this method to have a flashing LED with stable, regular interval flashes.
So Darrel's solution was a breath of fresh air (thanks Darrel - again)
I then got waylaid trying to work out some wayof getting my program, to 'remember' whether switch3 was last selected in 'mode 3' or 'mode 4' (I have an involved switching arrangement, where any of the 3 switches will turn the device on...once on, you can freely press another switch to move to ther other modes - but for user practicality, if the unit was switched on in mode3, then say switch 2 was pressed, when going back to switch 3, I'd reckon the player would want whichever mode he was last in with switch3 to be recalled - eeeuggh ...this is getting wordy & hard to describe so I'll digress!).
Darrel...good idea about 'any two...no matter which two' ....I'll mull that one over (might be better than me having to learn about timers for my situation!!). The wierd thing is that even though some ideas seem fine, when you come you actually use them ....they're not so good. My earlier example about holding swith3 longer to enter mode 4 - it just doesn't fit in with the intended applicated - fast switching for a guitarist going hell for leather!
Mike....all my switches use diodes.
Last edited by HankMcSpank; - 6th August 2010 at 10:57.
|
Hi Hank',
Got a schematic we could look at? Maybe there's a way to recover an extra pin that you haven't thought of.
How are you sampling and managing your switches? Polling them in a loop or polling them via periodic interrupt?
Are you using two pins for that tri-color LED or are you using any pins for LED mode indicators? If so, you might consider reclaiming those pins and using one of them for the fourth switch, then mux' the mode LEDs with the switches.
Regards, Mike
Last edited by Mike, K8LH; - 6th August 2010 at 14:03.
|
Here's the switching part....
(I know some consider it bad form, but I use the PIC's internal weak pullups, for no other reason than it saves space - and believe me, I need all the space I can get!)
...there are a few spare pins Pin on the 16f690, Pin 4 is somewhat restricted in its use, so I stay clear of it, Pin 9 is 'forsaken' so I can use that bit of track/pcb real estate to 'conduit' the +4.1V onwards to the rest of the PCB, Pins 6, 15, 16 & 19 are essentially 'landlocked' from a PCB track routing perspective
Yes, I'm using two pins (pins 2 & 3) for driving the LED (must remember to order common anode LEDs next time, so I can sink current from the main 9V VCC rail vs the PIC's 4V.1 rail ...puts less demand on the 100mA LDO regulator I've used!)
Re how am I sampling the switches? - using DT's mighty fine interupt routine.
There is no room for a fourth switch - likewise no room for illuminated switches - I'm only using 6mm square momentary push switches because they're the only ones I can shoehorn in.
The problem of course is the more 'modes' I offer (and it would be lovely to offer 6 or 7), is providing the guitarist with meaningful (rememberable) visual indication of the modes with just one LED ...green, amber & red is fine. ....squeezing in a 'flashing LED' for the extra mode is pushing it - any more modes, that it's going to be hell to remember what the LED is telling you! (& there's no room for a lcd, 7 seg display etc)
To give you some idea of my challenge, the pcb 'real estate' is about 40mm x70mm x 5.5mm high (1.5" x 3" x 0.2" high) - in that space I have to fit 2 x 20SOIC, 1 x 8 SOIC, 1 POT, 4 switches (the fourth switch is not at all related to this circuit), one single coil guitar pickup (that I make myself), one chunky electrolytic....and this is all on single sided pcb (along with a whole heap of 1206 SMD components) - it's crammed!
Last edited by HankMcSpank; - 6th August 2010 at 14:40.
Members who have read this thread : 0You do not have permission to view the list of names.
Posting Permissions
Bookmarks