Question on DT_Interrupts

[financecatalyst]

I use DT_INTERRUPT whenever I need to use interrupts. Having no knowledge of ASM, I find it much easier. I have always used it for 12F635. Recently I have tried to use DT_INT on 16F690 & 16F676 for one of my projects, but I failed to get results. I made sure I have right settings in DT_INT file and Re-Enter file.
1) FOR 16F690 I used

wsave       var byte    $70 ; in DT_INTS-14 file

& none of the Temp (T1,T2,T3,T4) variables where commented out.
Few lines from the code are the following which are not working to begin with:

Include "modedefs.bas"
INCLUDE "DT_INTS-14.bas"
INCLUDE "ReEnterPBP.bas"
DEFINE OSC 4

@ __Config _INTRC_OSC_NOCLKOUT & _WDT_OFF & _PWRTE_ON & _MCLRE_OFF & _BOR_ON & _CP_ON & _CPD_ON & _IESO_OFF & _FCMEN_ON
PAUSE 50
ANSEL=0
ANSELH=0
CM1CON0 = 0
CM2CON0 = 0

OPTION_REG=128
PORTB=0
PORTC = 0
PORTA = 0
TRISA = %001000
TRISC = 0
TRISB =0 

ASM
INT_LIST  macro    ; IntSource,        Label,  Type, ResetFlag?
 		      INT_Handler   TMR1_INT,  	  _CHECK,   PBP,  yes
    endm
    INT_CREATE               ; Creates the interrupt processor
ENDASM
T1CON=$E1
@ INT_ENABLE 	TMR1_INT
while 1
FOR W1=1 TO 10
TOGGLE PIN13
PAUSE 100
NEXT W1

FOR W1=1 TO 5
TOGGLE PIN13
PAUSE 1000
NEXT W1
wend

CHECK:
TOGGLE PIN11
@ INT_RETURN

PIC (690) does not responds to anything. When I use 676 then Pin11 on the PIC blinks couple of times and then stops and just glows continuesly along with pin13. Seems to me that wether DT_INTS are for selected PICs only or is there something I need to add/delete from the code to make it work on 676 & 690.
Has anyone else had issues with DT_INT for these PICs. I am looking forward to try them on 16F877A. Are there any known reliability issues with 877A?

[Bruce]

You have Timer1 configured to operate from the T1G gate input pin.

This works fine on the 690;

ASM
INT_LIST  macro    ; IntSource,        Label,  Type, ResetFlag?
         INT_Handler   TMR1_INT,     _CHECK,   PBP,  yes
    endm
    INT_CREATE               ; Creates the interrupt processor
ENDASM
   T1CON = %00110001
 
@ INT_ENABLE  TMR1_INT
 
  while 1
      FOR W1=1 TO 10
      TOGGLE PORTB.5
      PAUSE 100
    NEXT W1
 
    FOR W1=1 TO 5
      TOGGLE PORTB.5
      PAUSE 1000
    NEXT W1
  wend
 
CHECK:
    TOGGLE PORTB.6
@ INT_RETURN

[financecatalyst]

I will try it on 690 soon. Please answer on 16F676 as well.
Here is my code for 676:

Include "modedefs.bas"
INCLUDE "DT_INTS-14.bas"
INCLUDE "ReEnterPBP.bas"
DEFINE OCS 4
DEFINE OSC_1K 1

@ __Config _INTRC_OSC_NOCLKOUT & _WDT_ON & _PWRTE_ON & _MCLRE_OFF & _BODEN & _CP & _CPD

PAUSE 50
TRISA = %001000
TRISC = 0
PORTC = 0
PORTA = 0
CMCON = 7
ANSEL = 0
OPTION_REG=128

ASM
INT_LIST  macro    ; IntSource,        Label,  Type, ResetFlag?
        INT_Handler   TMR1_INT,  	  _CHECK,   PBP,  yes
    endm
    INT_CREATE               ; Creates the interrupt processor
ENDASM
T1CON=%00010001
@ INT_ENABLE TMR1_INT

while 1
    FOR code=1 TO 5
      TOGGLE pin8
      PAUSE 1000
    NEXT code
  wend

CHECK:
toggle pin7
i=i+1
if i=2 then
Portc=%000000
PORTC=0
i=0
endif
@ INT_RETURN

The led on Pin7 (in ISR) seems to be blinking at a constant rate BUT pin8 is erratic. Do I need to take care of any other setting as well? Thanks

[Bruce]

What is this? DEFINE OSC_1K 1

If you're trying to load the factory osccal value use DEFINE OSCCAL_1K 1.

Which physical pin is pin8 & where have you defined pin8?

If it's on PORTC, you're clearing this in your int handler (twice).