Sony IR Remote

[fratello]

After thousands of re-writing this code, I've got finally results :

@ DEVICE PIC12F675, INTRC_OSC_NOCLKOUT, wdt_off, pwrt_off, mclr_off, bod_off
DEFINE OSC 4

CMCON = 7               ' Comparators disabled
ANSEL = 0               ' A/D disabled

@ #define IRTX GPIO     ; Define port to use for IR out
@ #define PIN 1         ; Define port pin for IR out


 Puls_a         CON 112  ' 112 x 26uS = 2912 mS ( pulse with carrier ON)

InterPulse  CON 2800 ' 2.80mS (delay between pulses with carrier OFF)

Puls_b        CON 28   ' 28 x 26uS = 728 uS   ( pulse with carrier ON)





X        VAR BYTE ' Data bit loop counter & bit index pointer
Duration VAR BYTE ' Duration of button press
Loops    VAR BYTE ' Loop count
Cycles   VAR BYTE BANK0 SYSTEM' Number of carrier cycles to generate


trisio=%11111101
option_reg.7=0
wpu	=%11111101

but  var gpio.5

                        

    GOTO Main       ' Jump over pulse routine to Main
    
Pulse:              ' Generate "Cycles" number of 40kHz pulses
ASM                 ; Keep this routine in code page 1, and jump over to Main
   	BSF	IRTX,PIN		      ; 1 MAKE IR HIGH 35% Duty cycle = 9 uS
	GOTO	$+1
	GOTO	$+1
	GOTO	$+1
	GOTO	$+1
	BCF	IRTX,PIN		      ; 1 MAKE IR LOW 17 uS
	GOTO	$+1
	GOTO	$+1
	GOTO	$+1
	GOTO	$+1
	GOTO	$+1
	GOTO	$+1
	DECFSZ	Cycles,F	
	GOTO	_Pulse	      ; 2    26 uS
ENDASM
   return           ' Return to caller    
    
Main:

Duration = 2    ' Send it twice

IF BUT=0 THEN    
For Duration = 1 to 2
        Cycles = Synch         ' carrier on
        Call Puls_a             ' Send pulse

        PAUSEUS InterPulse    ' Pause (carrier off)

        Cycles = Logic0        ' carrier on
        Call Puls_b             ' Send pulse

		Pauseus 50000
		Pauseus 50000
Next Duration

ENDIF    
    GOTO Main                  ' Return for more

    END

This is command for Volume Up only ; instead 102 cycles * 26 uS = 2650 uS, I put 112 * 26 = 2912, etc. So, the lenght of one pulse is 23.5 uS ?! Maybe with this PIC... Anyway, it's good to see that working, after hard work... Thank You all for support; every advice it's further wellcome !

[Ioannis]

It seems that the internal RC oscilator is not precise at least for the receiver you use.

It cannot tolerate small differencies of the transmission pulse width.

Either use a crystal oscillator or trim your delays so that they get precisely the value needed.

Ioannis

[fratello]

Using PIC 16F628A I build this remote-by-wire for my Blaupunkt Radio-SD Card. Work verry fine... even it's simple and can be improved.

;
; Simple Remote-by-wire for Blaupunkt ; use RC10 protocol
;
@ DEVICE pic16F628A, XT_OSC, WDT_OFF, PWRT_OFF, BOD_OFF, MCLR_ON, LVP_OFF, CPD_OFF, PROTECT_OFF     

DEFINE  OSC 4      ; USE 4 MHz crystal                       

TRISA= %00000000                   
TRISB= %00011111 			
CMCON=7                                

TO_BLAU VAR PORTA.0
TO_BLAU = 1 

PULSA	VAR WORD
PULSB	VAR WORD
I	VAR BYTE

DELAYS  CON 660


MAIN :
PAUSE 500
    	IF PORTB.0 = 0 THEN        'volume +
    	PULSA=2650
    	PULSB=2580
    	GOSUB PULSE
    	ENDIF 


	IF PORTB.1 = 0 THEN        'volume -
	PULSA = 3250
	PULSB = 3200
	GOSUB PULSE
	ENDIF

	IF PORTB.2 = 0 THEN        'mute
    	PULSA = 5050
    	PULSB = 5000
	GOSUB PULSE
	ENDIF

    	IF PORTB.3 = 0 THEN        'SRC aka Source
	PULSA = 6875     
	PULSB = 6850     
    	GOSUB PULSE
	ENDIF

    	IF PORTB.4 = 0 THEN        'Next aka Right
	PULSA = 5660    
	PULSB = 5630     
    	GOSUB PULSE
	ENDIF
	
GOTO MAIN

;SUBROUTINE

PULSE:
	FOR I = 1 TO 10
		LOW TO_BLAU
		PAUSEUS PULSA
		HIGH TO_BLAU
		PAUSEUS PULSB
		LOW TO_BLAU
		PAUSEUS DELAYS
		HIGH TO_BLAU
		PAUSEUS 50000
		PAUSEUS 50000
	NEXT I	
RETURN

END