Anyone used the Bosch BMP085 I2C baro sensor yet ?

[Acetronics2]

Hi, Sneezzy

I Think , with little trickery, the 16F84 could fit ...

let's think ...

IF you calculate the linearisation OUTSIDE the Pic, and trunk it to the PRECISION claimed ( not the resolution, eh ...)
...

I'm sure a lookup table, or a couple of " ax+b " regressions could be used.

But that implies ... the sensor and the PIC are married for life !!!

Alain

[mr.sneezy]

Hi, Sneezzy

I Think , with little trickery, the 16F84 could fit ...

let's think ...

IF you calculate the linearisation OUTSIDE the Pic, and trunk it to the PRECISION claimed ( not the resolution, eh ...)
...

I'm sure a lookup table, or a couple of " ax+b " regressions could be used.

But that implies ... the sensor and the PIC are married for life !!!

Alain

I did think of that early on. I think you need to map all possible pressure readings (at your needed precision) across your range, but then also map for every possible temperature change across all pressure readings in that range. I think it very quickly becomes an impressive size lookup table yes ?
I suspect my shorts are safe, but if the poster above can do it I'll listen :-)

[Acetronics2]

Hi, Martin

I had a look to your excel sheet and , of course, got THE problem ...

solution was to unlock the sheet , select the "F16" place and click on " place a formula " ( Fx button ) ...

it automatically corrects the written formula and then it rolls fine !!!

Are the Calibration values in the sheet those of YOUR Sensor ???

Alain

[mr.sneezy]

Hi, Martin

I had a look to your excel sheet and , of course, got THE problem ...

solution was to unlock the sheet , select the "F16" place and click on " place a formula " ( Fx button ) ...

it automatically corrects the written formula and then it rolls fine !!!

Are the Calibration values in the sheet those of YOUR Sensor ???

Alain

Hi Alain, I suspect my friend didn't tell me that so I couldn't fiddle with his sheet

Yes, that indeed is the calibration data out of my BMP085 sensor.

Good news.
Tonight I finished debugging the pressure calculations and got a correct result in Pascals. Boy it took some doing didn't it. :-)
Tomorrow I'll tidy up the code and post the whole job after doing a little field testing.

Now I need to find a sample of a 'good' way to do a look-up table to convert pressure to altitude without using Logs (as I understand is required)...

Martin

[Acetronics2]

Hi, Martin

Was an awful job to crack the sheet password I had to wait for the second attempt to get it open ...

May be ...

an excel sheet could easily produce the retrieve table to include in the program ???

I already did that for a programmable electronic ignition project ...

Alain

[rore85]

Thanks for answer...
I wonder if the calibration coefficients of BMP085 depend on something ... as either light, or are the same constants for all?
And another thing, the uncompensated temperature varies a lot ... in the order of thousands or hundreds
Thanks

[mr.sneezy]

Thanks for answer...
I wonder if the calibration coefficients of BMP085 depend on something ... as either light, or are the same constants for all?
And another thing, the uncompensated temperature varies a lot ... in the order of thousands or hundreds
Thanks

Mainly temperature dependant. I've not been able to show much sensitivity to light yet (indoors).
Yes, the pressure reading is very 'active' so I used the maximum OSS and then 10x averaging as well. It could do with even more...

[rore85]

Thanks for answer...
I wonder if the calibration coefficients of BMP085 depend on something ... as either light, or are the same constants for all?
And another thing, the uncompensated temperature varies a lot ... in the order of thousands or hundreds
Thanks

Hi everybody...
The program in assembler works but I have problems generated in a division ratio, ie, it is rounded to an integer and the final value of the temperature goes too far in the real value, almost 80 degrees more ...
Someone had the same problem?
Thanks in advance!

[mr.sneezy]

Hi, Martin

Was an awful job to crack the sheet password I had to wait for the second attempt to get it open ...

May be ...

an excel sheet could easily produce the retrieve table to include in the program ???

I already did that for a programmable electronic ignition project ...

Alain

Yes, I guess it could be done that way. I wonder how much data in the table is just enough, that might be hard to workout ?
Yes the sensor would be mated by the table to one PIC for life, and make it impossible to give the HEX file to anyone else to use for an open project (if they can't use PBP). Unless the table can be forced into a known place in code space perhaps... Messy at the very least.

[eab123]

Hi Martin-
Thanks for sharing the Bosch code with us- some undertaking.
I'm just about to start a small project that could use this device and thought I'd just check I can compile it correctly using your posted code for the 18F4620 before proceeding further.

Unfortunately I'm getting compile errors ("overwriting previous address contents 0000 to 0007 locations") and just wondering if you could give me the versions of Microstudio and PBP you are running- I'm running Microstudio 3.0.0.5 and PBP 2.50L (with the pbpl box checked!)
Thanks for your time.
Edward