GPS module + PIC

**mackrackit** · - 10th April 2010, 13:50

10001000000
is the number excel failed on but other than that I do not know. I will have to look into it.

**ScaleRobotics** · - 10th April 2010, 14:14

Here is one check sum solution for gps:

Code:

gpsdata         var byte[82]       ' Max length of a GPS sentence is 82 bytes.

DoCS:
    i = 0                             ' Initialize the position counter
                
    WHILE gpsdata[i] != "*"           ' Count everthing until the *
        cs = cs ^gpsdata[i]           ' XOR for checksum
        i = i + 1                     ' Increment position counter
    WEND

    ' A quick and easy atoh function
    ' Make it a seperate label if we add more atoh conversions in the future
    LOOKDOWN gpsdata[i+1],["0123456789ABCDEF"],tempbyte
    gpscs = tempbyte * 16        
    LOOKDOWN gpsdata[i+2],["0123456789ABCDEF"],tempbyte                
    gpscs = gpscs + tempbyte
        
    ' Flag bad data "V" if checksum doesn't add up. 
    ' Or if the sentence is less then 20 chars long
    ' Which means there is no active waypoint to go to.
    ' Should be "A" otherwise.
    IF (cs != gpscs) OR (i < 20 )THEN 
          gpsvalid = 0
    ELSE 
          gpsvalid = 1
    ENDIF   
RETURN

**flotulopex** · - 16th April 2010, 12:32

- Reading & parsing NMEA sentences is ok;
- Calculating checksum is ok;
- Sending data to GPS module is not ok.

I have connected the GPS module via the MAX232 chip to my serial PC port both ways so I should be able to "talk" to my module.

Unfortunately, only reading out (receiving) the GPS module is working.

I checked the MAX chip with my oscillo and the signals are okay (TX & RX) on both levels (RS232 and TTL).

I'm sending an example from the module's datasheet to enable a VTG sentence but it won't work.

<img src="http://www.picbasic.co.uk/forum/attachment.php?attachmentid=4205&stc=1&d=127141338 1">

I just never see this VTG data appear.

<img src="http://www.picbasic.co.uk/forum/attachment.php?attachmentid=4207&stc=1&d=127141381 2">

Any idea?

**flotulopex** · - 16th April 2010, 12:49

Strange....

I just restarted the terminal and... it works now - I can sent messages to the module.

Must be a kind of magic (?)

**Ioannis** · - 16th April 2010, 16:29

Is it Hyperterminal?

Ioannis

**flotulopex** · - 18th April 2010, 21:26

No, it's MicroCode Studio's terminal.

But I checked with HT too and did the same (?).

Nevermind, it works now

**flotulopex** · - 22nd April 2010, 09:51

Hello there,

I just finished this piece of code and it works fine. It will simply display the GPS course & speed.

I finally connected the GPS module's TX directly to a TTL port of my PIC (no level-shifter such as MAX232 used) with the correspondant mode settings.

Everything is working fine appart from the NOGPS routine.

When I disconnect the GPS's TX from the PIC's port, the NOGPS routine will never appear.

Any idea what's wrong?

Code:

<html><head></head><body><!--StartFragment--><pre><code><font color="#000080"><i>' PIC 16F690 Fuses
</i></font><font color="#008000">@ DEVICE FCMEN_OFF
@ DEVICE IESO_OFF
@ DEVICE BOD_OFF
@ DEVICE CPD_OFF
@ DEVICE PROTECT_OFF
@ DEVICE MCLR_OFF
@ DEVICE PWRT_OFF
@ DEVICE WDT_OFF
@ DEVICE XT_OSC

</font><font color="#000080"><i>' Registers   76543210
</i></font>OPTION_REG = %10000000 <font color="#000080"><i>'PORT A&amp;B Pull-Ups disabled (look WPUA &amp; WPUB)
</i></font>ANSEL      = %00000000 <font color="#000080"><i>'Disable analog inputs Channels 0 to 7
</i></font>ANSELH     = %00000000 <font color="#000080"><i>'Disable analog inputs Channels 8 to 11
</i></font>ADCON0     = %00000000 <font color="#000080"><i>'A/D Module is OFF
</i></font>CM1CON0    = %00000000 <font color="#000080"><i>'Comparator1 Module is OFF
</i></font>CM2CON0    = %00000000 <font color="#000080"><i>'Comparator2 Module is OFF
</i></font>INTCON     = %00000000 <font color="#000080"><i>'INTerrupts CONtrol
</i></font>TRISA      = %00000001 <font color="#000080"><i>'Set Input/Output (0 to 5)
</i></font>PORTA      = %00000000 <font color="#000080"><i>'Ports High/Low (0 to 5)
</i></font>TRISB      = %00000000 <font color="#000080"><i>'Set Input/Output (4 to 7)
</i></font>PORTB      = %00000000 <font color="#000080"><i>'Ports High/Low (4 to 7)
</i></font>TRISC      = %00000000 <font color="#000080"><i>'Set Input/Output (0 to 7)
</i></font>PORTC      = %00000000 <font color="#000080"><i>'Ports High/Low (0 to 7)

'-------------------------------------------------------------------------------
' LCD cabling
'-	    ( 1) Vss - GND
'-	    ( 2) Vdd / Vcc +5V
'-	    ( 3) Vee / Vo / Contrast adjust / Pot 4k7(1-2-W3) or R2k2(GND-3)
'PORTC.1    ( 4) RS
'-	    ( 5) R/W -&gt; to Vss
'PORTC.2    ( 6) E
'PORTB.4    (11) D4
'PORTB.5    (12) D5
'PORTB.6    (13) D6
'PORTB.7    (14) D7

</i></font><b>DEFINE </b>LCD_DREG PORTB  <font color="#000080"><i>'LCD data port 
</i></font><b>DEFINE </b>LCD_DBIT 4      <font color="#000080"><i>'LCD data starting PORT.bit (0 or 4)
</i></font><b>DEFINE </b>LCD_RSREG PORTC <font color="#000080"><i>'LCD register select port 
</i></font><b>DEFINE </b>LCD_RSBIT 1     <font color="#000080"><i>'LCD register select bit 
</i></font><b>DEFINE </b>LCD_EREG PORTC  <font color="#000080"><i>'LCD enable port 
</i></font><b>DEFINE </b>LCD_EBIT 2      <font color="#000080"><i>'LCD enable bit 
</i></font><b>DEFINE </b>LCD_BITS 4      <font color="#000080"><i>'LCD bus size 4 or 8 
</i></font><b>DEFINE </b>LCD_LINES 2     <font color="#000080"><i>'Number lines on LCD 

'-------------------------------------------------------------------------------
</i></font>INIT:
Ctr_A       <b>VAR BYTE    </b><font color="#000080"><i>'Counter
</i></font>GPS_D       <b>VAR BYTE</b>(80)<font color="#000080"><i>'Incomming data bit array
</i></font>Spd_U       <b>VAR WORD    </b><font color="#000080"><i>'Speed Units
</i></font>GPSfrom     <b>VAR </b>PORTA.0 <font color="#000080"><i>'use a TTL I/O port on PIC!
</i></font>GPSbps      <b>VAR WORD
</b>GPSbps      = 32956     <font color="#000080"><i>'Open,True,N,4800bps (TTL level)
</i></font>Timeout     <b>CON </b>3000
CommaCnt    <b>VAR BYTE    </b><font color="#000080"><i>'comma count

</i></font><b>PAUSE </b>1000
<b>LCDOUT </b>$FE, 1

<font color="#000080"><i>' Custom character definition
</i></font><b>LCDOUT </b>$FE,$40,$0C,$12,$12,$0C,$00,$00,$00,$00 <font color="#000080"><i>'character 0 = &quot;&deg;&quot;
</i></font><b>LCDOUT </b>$FE,$48,$14,$18,$14,$00,$1E,$15,$15,$00 <font color="#000080"><i>'character 1 = &quot;km&quot;

</i></font><b>LCDOUT </b>$FE,2,<font color="#FF0000">&quot;GPS v1.1&quot;
</font><b>PAUSE </b>3000

<font color="#000080"><i>'-------------------------------------------------------------------------------
</i></font>GPVTG:
<font color="#000080"><i>' Get VTG sentence and store it into GPS_D var until &quot;*&quot; is found
</i></font><b>SERIN2 </b>GPSfrom,GPSbps,Timeout,NOGPS,[WAIT(<font color="#FF0000">&quot;$GPVTG,&quot;</font>),<b>STR </b>GPS_D\<font color="#FF0000">&quot;*&quot;</font>]

<font color="#000080"><i>' extract COURSE data
</i></font>Ctr_A = 0
cou_u = 0
<b>WHILE </b>GPS_D(Ctr_A) != <font color="#FF0000">&quot;.&quot;
    </font>Cou_u = 10 * cou_u + (GPS_D(Ctr_A)-48)
    Ctr_A = Ctr_A + 1
<b>WEND

</b><font color="#000080"><i>' locate SPEED data after 6th comma
</i></font>Ctr_A = 0
CommaCnt = 0
<b>WHILE </b>CommaCnt &lt; 6
    <b>IF </b>GPS_D(Ctr_A) = <font color="#FF0000">&quot;,&quot; </font><b>THEN </b>CommaCnt = CommaCnt + 1
    Ctr_A = Ctr_A + 1
<b>WEND

</b><font color="#000080"><i>' extract SPEED data - leave tenths
</i></font>Spd_U = 0
<b>WHILE </b>GPS_D(Ctr_A) != <font color="#FF0000">&quot;.&quot;
    </font>Spd_U = 10 * Spd_U + (GPS_D(Ctr_A)-48)
    Ctr_A = Ctr_A + 1
<b>WEND

LCDOUT </b>$FE,1
<b>LCDOUT </b>$FE,2,<b>DEC </b>cou_u,0,<font color="#FF0000">&quot; &quot;</font>,<b>DEC </b>Spd_U,1
<b>GOTO </b>GPVTG:

<font color="#000080"><i>'-------------------------------------------------------------------------------
</i></font>NOGPS: 
<b>LCDOUT </b>$FE,2,<font color="#FF0000">&quot; No GPS &quot;
</font><b>PAUSE  </b>1000 
<b>GOTO </b>GPVTG:

<b>END
</b></code></pre><!--EndFragment--></body>
</html>

Thread: GPS module + PIC

Thread Tools

Search Thread

Display

Hybrid View

Check Sum

Can't "talk" towards my GPS module...

It works now!

Timeout routine not working

Members who have read this thread : 2

Bookmarks

Bookmarks

Posting Permissions