DEFINE OSC Serout problem

[Bonxy]

@ __CONFIG   _CONFIG1L, _PLLDIV_5_1L & _CPUDIV_OSC1_PLL2_1L & _USBDIV_2_1L
@ __CONFIG   _CONFIG1H, _FOSC_HSPLL_HS_1H
DEFINE OSC 48

Should work?

The external OSC does not matter to PBP here. The above should have the MCU running at 48MHz. That is what PBP cares about.

Hey mackrackit

The DEFINE OSC 48 works!, although I dont understand why (the crystal is still 20mhz), but who cares, both usb and serout are working now.

Thanks dude

[ScaleRobotics]

The DEFINE OSC 48 works!, although I dont understand why (the crystal is still 20mhz), but who cares, both usb and serout are working now.

It is because you have to have the OSC configuration settings correct. And with so many options with these PIC18 chips, you have to read the data sheet a lot of times to get them right. (At least that is speaking for myself!) If you have (almost) any one of them set incorrectly, you will be running at the wrong speed, or worse, not run at all. But it does give you great flexibility.

Here are your config options just for the oscillator on a pic18f4550:

;----- CONFIG1L Options --------------------------------------------------
_PLLDIV_1_1L         EQU  H'F8'    ; No prescale (4 MHz oscillator input drives PLL directly)
_PLLDIV_2_1L         EQU  H'F9'    ; Divide by 2 (8 MHz oscillator input)
_PLLDIV_3_1L         EQU  H'FA'    ; Divide by 3 (12 MHz oscillator input)
_PLLDIV_4_1L         EQU  H'FB'    ; Divide by 4 (16 MHz oscillator input)
_PLLDIV_5_1L         EQU  H'FC'    ; Divide by 5 (20 MHz oscillator input)
_PLLDIV_6_1L         EQU  H'FD'    ; Divide by 6 (24 MHz oscillator input)
_PLLDIV_10_1L        EQU  H'FE'    ; Divide by 10 (40 MHz oscillator input)
_PLLDIV_12_1L        EQU  H'FF'    ; Divide by 12 (48 MHz oscillator input)

_CPUDIV_OSC1_PLL2_1L EQU  H'E7'    ; [OSC1/OSC2 Src: /1][96 MHz PLL Src: /2]
_CPUDIV_OSC2_PLL3_1L EQU  H'EF'    ; [OSC1/OSC2 Src: /2][96 MHz PLL Src: /3]
_CPUDIV_OSC3_PLL4_1L EQU  H'F7'    ; [OSC1/OSC2 Src: /3][96 MHz PLL Src: /4]
_CPUDIV_OSC4_PLL6_1L EQU  H'FF'    ; [OSC1/OSC2 Src: /4][96 MHz PLL Src: /6]

_USBDIV_1_1L         EQU  H'DF'    ; USB clock source comes directly from the primary oscillator block with no postscale
_USBDIV_2_1L         EQU  H'FF'    ; USB clock source comes from the 96 MHz PLL divided by 2

;----- CONFIG1H Options --------------------------------------------------
_FOSC_XT_XT_1H       EQU  H'F0'    ; XT oscillator, XT used by USB
_FOSC_XTPLL_XT_1H    EQU  H'F2'    ; XT oscillator, PLL enabled, XT used by USB
_FOSC_ECIO_EC_1H     EQU  H'F4'    ; External clock, port function on RA6, EC used by USB
_FOSC_EC_EC_1H       EQU  H'F5'    ; External clock, CLKOUT on RA6, EC used by USB
_FOSC_ECPLLIO_EC_1H  EQU  H'F6'    ; External clock, PLL enabled, port function on RA6, EC used by USB
_FOSC_ECPLL_EC_1H    EQU  H'F7'    ; External clock, PLL enabled, CLKOUT on RA6, EC used by USB
_FOSC_INTOSCIO_EC_1H EQU  H'F8'    ; Internal oscillator, port function on RA6, EC used by USB
_FOSC_INTOSC_EC_1H   EQU  H'F9'    ; Internal oscillator, CLKOUT on RA6, EC used by USB
_FOSC_INTOSC_XT_1H   EQU  H'FA'    ; Internal oscillator, XT used by USB
_FOSC_INTOSC_HS_1H   EQU  H'FB'    ; Internal oscillator, HS used by USB
_FOSC_HS_1H          EQU  H'FC'    ; HS oscillator, HS used by USB
_FOSC_HSPLL_HS_1H    EQU  H'FE'    ; HS oscillator, PLL enabled, HS used by USB

_FCMEN_OFF_1H        EQU  H'BF'    ; Fail-Safe Clock Monitor disabled
_FCMEN_ON_1H         EQU  H'FF'    ; Fail-Safe Clock Monitor enabled

_IESO_OFF_1H         EQU  H'7F'    ; Oscillator Switchover mode disabled
_IESO_ON_1H          EQU  H'FF'    ; Oscillator Switchover mode enabled

Walter

[mackrackit]

And...
The OSC is not running the chip, it is running the PLL, That is why the 48MHz works.
With the correct config settings you can run at 48MHz with a 4MHz external.

Another cool thing is the different voltages this allows. Normally you have to use 5 volts to run a chip at 20MHz, with a 4MHz and the correct configs you can run this chip with 2 volts at 48MHz. For USB though you will not want to go lower than 3.3 volts, so that way the whole system can run at "low" voltages at "high" speeds. Really nice when using things like SD cards, some RTC, and other things that only run on ~3 volts.