TTL magnetic card reader reads but unprintable char
hello every one
I have TTL card reader connected with pic18f4620 on port B
Im using the driver found with picc compiler (ex_mcr)
which is supposed to read magnetic card correctly
the problem that it reads , but the data are not correct --> not printable characters
like this..(w??n?]??)
I have been searching but finding nothing to help
the number of characters is also not correct.
I tried many different magnetic cards but nothing worked well.
here is the code..
this is the driver
Any suggestions ...Code:// Redefine the following pins in // the main file as needed. #ifndef MCR_CARD_PRESENT #define MCR_CARD_PRESENT PIN_B0 #define MCR_DATA1 PIN_B1 #define MCR_STROBE1 PIN_B2 #define MCR_DATA2 PIN_B4 #define MCR_STROBE2 PIN_B5 #endif // The following define the error codes. // To check for a specific error, check // the cooresponding bit in the value // returned by mcr_read(). #define MCR_ERR_PARITY1 1 #define MCR_ERR_PARITY2 2 #define MCR_ERR_LRC1 4 #define MCR_ERR_LRC2 8 // Date: 7/28/2003 int mcr_read(char* track1, char* track2) { int error = 0; int1 dataBit = 0; int1 ST1 = 1; int1 ST1_old = 1; int1 firstOne1= 0; int1 parity1 = 0; int count1 = 0; int index1 = 0; int LRC1 = 0; int1 ST2 = 1; int1 ST2_old = 1; int1 firstOne2= 0; int1 parity2 = 0; int count2 = 0; int index2 = 0; int LRC2 = 0; // Wait for card to be present while(input(MCR_CARD_PRESENT)) { // printf("outside\n"); restart_wdt(); } // Loop until a card is not present while(!input(MCR_CARD_PRESENT)) { // printf("inside\n"); restart_wdt(); // Check for NULL pointer and an index less than 79 if(track1 != 0 && index1 < 79) { // Get strobe number one ST1 = input(MCR_STROBE1); restart_wdt(); // If the strobe was high and is now low (falling edge), // then data is present if(ST1 == 0 && ST1_old == 1) { ST1_old = 0; // Check if the first 1 was received if(firstOne1 == 1) { // Check if 6 bits of data were received if(count1 == 6) { // Set the data bit count back to 0 count1 = 0; // Shift the bits right by 2 *(track1+index1) >>= 2; // Verify the LRC if(*(track1+index1-1) == '?' && LRC1 != *(track1+index1)) { error |= MCR_ERR_LRC1; } else { LRC1 ^= *(track1+index1); } // Add 0x20 to convert to ASCII *(track1+index1) += 0x20; // Check the parity bit. The parity on a space is not checked // because of the trailing zeros after the LRC character if(!input(MCR_DATA1) != parity1 && *(track1+index1) != ' ') { error |= MCR_ERR_PARITY1; } // Reset the parity check parity1 = 1; // Increment the index into the array ++index1; } else { // Get a bit of data from the card dataBit = !input(MCR_DATA1); // XOR the data with the parity bit parity1 ^= dataBit; // Store the new bit of data shift_right(track1+index1, 1, dataBit); // Increment the bit counter ++count1; } } else { // Check if the first 1 has appeard on the data line if(!input(MCR_DATA1)) { // Set the first 1 received flag firstOne1 = 1; // Store the first 1 shift_right(track1, 1, 1); // Increment the bit counter ++count1; } } } else if(ST1 == 1) { ST1_old = 1; } } // our code // printf("%c\n",track1[index1]); // if(track1[index1]=='?') // { // return error; // } // // Check for NULL pointer and an index less than 40 if(track2 != 0 && index2 < 40) { // Get strobe number 2 ST2 = input(MCR_STROBE2); // If the strobe was high and is now low (falling edge), // then data is present if(ST2 == 0 && ST2_old == 1) { ST2_old = 0; // Check if the first 1 was received if(firstOne2 == 1) { // Check if 4 bits of data were received if(count2 == 4) { // Reset the bit counter back to 0 count2 = 0; // Shift the bits right by 4 *(track2+index2) >>= 4; // Verify the LRC if(*(track2+index2-1) == '?' && LRC2 != *(track2+index2)) { error |= MCR_ERR_LRC2; } else { LRC2 ^= *(track2+index2); } // Add 0x30 to convert to ASCII *(track2+index2) += 0x30; // Check the parity bit. The parity on a 0 is not checked // because of the trailing zeros after the LRC character if(!input(MCR_DATA2) != parity2 && *(track2+index2) != '0') { error |= MCR_ERR_PARITY2; } // Reset the parity check parity2 = 1; // Increment the index into the array ++index2; } else { // Get a bit of data from the card dataBit = !input(MCR_DATA2); // XOR the data with the parity bit parity2 ^= dataBit; // Store the new bit of data shift_right(track2+index2, 1, dataBit); // Increment the bit counter ++count2; } } else { // Check if the first 1 has appeard on the data line if(!input(MCR_DATA2)) { // Set the first 1 received flag firstOne2 = 1; // Store the first 1 shift_right(track2, 1, 1); // Increment the bit counter ++count2; } } } else if(ST2 == 1) { ST2_old = 1; } } } // Return any errors return error; }
thanks alot
change the calculator Batt or clean glasses ???
Bookmarks