Talat

I do not understand why you included the lines in red in you ISR

Code:
'************************************************* ***************
'* Name : *
'* Author : [select VIEW...EDITOR OPTIONS] *
'* Notice : Copyright (c) 2011 [select VIEW...EDITOR OPTIONS] *
'* : All Rights Reserved *
'* Date : 09.08.2014 *
'* Version : 1.0 *
'* Notes : 16F1827 *
'* : *
'************************************************* ***************
' DEVİCE 16F1827

ASM
__config _CONFIG1, _FOSC_INTOSC & _WDTE_OFF & _PWRTE_ON & _MCLRE_OFF & _CP_OFF & _CPD_OFF & _BOREN_ON & _CLKOUTEN_OFF & _IESO_OFF & _FCMEN_OFF
__config _CONFIG2, _PLLEN_ON & _LVP_OFF & _LVP_OFF & _STVREN_OFF; & _VCAPEN_OFF
ENDASM
CLEAR
DEFINE OSC 32
OSCCON=%01110000 '32

DEFINE INTHAND PWM_INT

PWM_VAL VAR WORD BANK0 SYSTEM
VALUE VAR WORD

INIT:
APFCON0 = 0 'SET PORTB.3 TO CCP1
T1CON = %00100000 'Prescaler 1:4

PIE1.0 = 1 'TMR1IE TMR1 Interrupt Enable
PIR1.0 = 0 'TMR1IF TMR1 Interrupt Flag
INTCON.7 = 1 'GIE Global Interrupt Enable
INTCON.6 = 1 'PEIE Peripheral Interrupt Enable
CCP1CON = 9 'compare mode
OUTPUT PORTB.3 'CCP PIN


T1CON.0 = 1 'TMR1ON SET TMR1
PAUSE 1000
VALUE=1000

MLOOP:
VALUE=VALUE+1
PWM_VAL = VALUE
Goto MLOOP


Asm
PWM_INT
movlw 9 ; compare mode
clrf CCP1CON ; clear reg
movwf CCP1CON ; Set reg
movf PWM_VAL+1,W ; hb
movwf CCPR1H ; put
movf PWM_VAL,W ; lb
movwf CCPR1L ; put
bsf INTCON,7 ;GIE = 1
bsf INTCON,6 ;PEIE = 1 Enable peripheral interrupts
bsf PIE1,0 ; TMR1IE= 1 Enable TMR1
bcf PIR1,0 ; TMR1IF = 0 Clear Timer1 Int Flag

RETFIE ; Return from Interrupt
EndAsm

END
As I do not have a 16F1827 I can not do any testing. But after some thought I used an 18F452 to test your code and it did not work. I then compared data sheets for the 16F1827 and 18F452 and finding no reason for the lines in red I commented them out reprogramed the 18F452 and it ran. But I had to add a pause 10 in the main loop so my voltmeter could display the readings.

Here is my version

Code:
'************************************************* ***************
'* Name : *
'* Author : [select VIEW...EDITOR OPTIONS] *
'* Notice : Copyright (c) 2011 [select VIEW...EDITOR OPTIONS] *
'* : All Rights Reserved *
'* Date : 09.08.2014 *
'* Version : 1.0 *
'* Notes : 16F1827 *
'* : *
'************************************************* ***************
' DEVİCE 16F1827

ASM
__config _CONFIG1, _FOSC_INTOSC & _WDTE_OFF & _PWRTE_ON & _MCLRE_OFF & _CP_OFF & _CPD_OFF & _BOREN_ON & _CLKOUTEN_OFF & _IESO_OFF & _FCMEN_OFF
__config _CONFIG2, _PLLEN_ON & _LVP_OFF & _LVP_OFF & _STVREN_OFF; & _VCAPEN_OFF
ENDASM
CLEAR
DEFINE OSC 32
OSCCON=%01110000 '32

DEFINE INTHAND PWM_INT

PWM_VAL VAR WORD BANK0 SYSTEM


INIT:
APFCON0 = 0 'SET PORTB.3 TO CCP1
T1CON = %00100000 'Prescaler 1:4

PIE1.0 = 1 'TMR1IE TMR1 Interrupt Enable
PIR1.0 = 0 'TMR1IF TMR1 Interrupt Flag
INTCON.7 = 1 'GIE Global Interrupt Enable
INTCON.6 = 1 'PEIE Peripheral Interrupt Enable
CCP1CON = 9 'compare mode
OUTPUT PORTB.3 'CCP PIN


T1CON.0 = 1 'TMR1ON SET TMR1
PAUSE 1000


MLOOP:
PWM_VAL = PWM_VAL+1
PAUSE 10
Goto MLOOP


Asm
PWM_INT
movlw 9 ; compare mode
clrf CCP1CON ; clear reg
movwf CCP1CON ; Set reg
movf PWM_VAL+1,W ; hb
movwf CCPR1H ; put
movf PWM_VAL,W ; lb
movwf CCPR1L ; put
bcf PIR1,0 ; TMR1IF = 0 Clear Timer1 Int Flag

RETFIE ; Return from Interrupt
EndAsm

END
I am very interested to know if my version works on the 16F1827 that you have.