PBP projects for R/C models

[Bruce]

Hi Alain,

Yes. It's the 8-pin PIC12F1822.

 Enhanced Mid-range Core with 49 Instruction, 16 Stack Levels
 Flash Program Memory with self read/write capability
 Internal 32MHz oscillator
 Integrated Capacitive mTouch Sensing Module
 Data Signal Modulator Module
 MI2C, SPI, EUSART w/auto baud
 ECCP (Enhanced/Capture Compare PWM) Module
 Comparator with selectable Voltage Reference
 4 Channel 10b ADC with Voltage Reference
 25mA Source/Sink current I/O
 Two 8-bit Timers (TMR0/TMR2)
 One 16-bit Timer (TMR1)
 Extended Watchdog Timer (EWDT)
 Enhanced Power-On/Off-Reset
 Brown-Out Reset (BOR)
 In Circuit Serial Programming (ICSP)
 On Board In-Circuit Debug
 Wide Operating Voltage (1.8V – 5.5V)
 Low Power PIC12LF182x variants (1.8V – 3.6V)
 Standby Current (PIC12LF182X):  30 nA @ 1.8V, typical

[Kenjones1935]

Guys and Gals,

I might take a side trip to a scenic view along this road.

Here is a pointer to a BASIC (which BASIC I do not know) program that controls a toy level RC car. Toy levels have no Electronic Speed Control. The DC motor and servo are driven by direct current controlled by four DPDT switches. (Bang-Bang: full speed forward, full stop, full speed back.) This project has only autonomous control. The radio receiver has been eliminated. These simplifications plus the fact that the details are on the WEB make this diversion very tempting.

http://letsmakerobots.com/files/wall_racers.bas
and
http://letsmakerobots.com/node/928

I have an appropriate RC car.
I have a spare PICkit2.
I need to translate wall_racers.bas into PBP.
I need to adapt the resulting ASM to my 16F887.
I think I have enough proto. parts for both projects.

My ego needs a boost.

Ken:

[mackrackit]

Ken,

You are kind, intelligent, and I hear good looking.

There is your ego boost

Your new approach does sound like a good way to start. Save the PWM for later and work on the other parts.

You may want to think about what Bruce said and go "modular". Then when you do get back to the PWM part it could live on a separate chip.

You said you have some solder-less breadboards, so you could get a few of the 8 or 14 pin chips with ADC to play with. Remember MicrChip has a samples program so you could get three from them to start.

[Kenjones1935]

On the other hand==>

Look at this great oscilloscope-like picture of the PWM pulses (fifty per second) very close to 1.75ms long created by Bruce's PAUSEUS technique. I finally figured out the Analyzer part of the PICkit 2 Logic Tool.

Ken

[ScaleRobotics]

On the other hand==>

Look at this great oscilloscope-like picture of the PWM pulses (fifty per second) very close to 1.75ms long created by Bruce's PAUSEUS technique. I finally figured out the Analyzer part of the PICkit 2 Logic Tool.

Ken

Now that's progress! Great job Ken. That a pretty nice looking scope, and the price makes it look even better!

Now you can see what you are doing .... er (or not doing).

[Kenjones1935]

Fritsl's code compiles and runs on my PICkit2.

The proximity detector (Devantech SRF05) responds with different size pulses (depending on the distance from it to an echoing object) when queried by this code.

Next to prove out control of the four DPDT switches which steer DC to the motor and to the servo, destroy the toy car by ripping out its radio receiver. and figure out how to mount the PICkit, the switches board and the two SRF05's.

Question. Is there any way that I can read through the PICkit programmer what is happening in real time to some of the variables. How do I think about adding debugging code?

Ken

[ScaleRobotics]

In case someone wants to measure multiple RC channels with one CCP1 pin, I did a small expermiment. If you connect every other RC receiver channel to CCP pin using 1N914 diodes (or similar), you will be able to measure pulses from three (or four) RC channels using one pin. Without the diodes, the RC channels that are low, ground out the one that is trying to pulse.

Here is a picture of RC channels 2,4, and 6. Without a channel space between them, they stay high. So, with a PIC that has two CCP pins, you should be able to read all 8 channels!

This picture shows scope yellow probe (rc 2, 4, and 6) with their diodes attached to the scope probe. and scope red probe directly attached to RC channel 2.