Adding TCP/IP Ethernet to PIC - how?

[dhouston]

If you are in the USA you should avoid Tibbo like the plague. They have discontinued some of their devices with absolutely no warning (obviously due to patent infringement issues) and repeatedly misrepresented why they were discontinued and when they would offer a replacement.

[gtvmarty]

I'm in Australia, but it sounds like i shouldn't touch it at all no matter 'where' i am

Thanx for the headsup.
Marty.

If you are in the USA you should avoid Tibbo like the plague. They have discontinued some of their devices with absolutely no warning (obviously due to patent infringement issues) and repeatedly misrepresented why they were discontinued and when they would offer a replacement.

[comwarrior]

net232... i'm guessing HS serial to ETH remodulator... like the max232?

[Charles Linquis]

I'll add my favorite, the Lantronix XPort. I have thousands of them connected to PICs, and they are very reliable.
You can configure them from the "network side" or the PIC side (RS-232).

[dhouston]

I like ConnectOne's nano LanReach. It does e-mail.

• http://www.connectone.com/products.asp?did=73&pid=93

or, if you can use an external adapter and don't need e-mail

• http://www.ewiznet.com/goods_detail.php?goodsIdx=115

[Dave]

Charles Linquis, The NET232 is based on the Lantronix XPort. I do like the configuration over the network..

Dave Purola,
N8NTA

[l_gaminde]

I like ConnectOne's nano LanReach. It does e-mail.

• http://www.connectone.com/products.asp?did=73&pid=93

or, if you can use an external adapter and don't need e-mail

• http://www.ewiznet.com/goods_detail.php?goodsIdx=115

I have also used the connectone iChip it had good software and could do most of what you want but there were things missing and just wrong for general hookup.

1. Its a 3.3 volt device so you must be running @ 3.3 or use an adapter !

2. Its pin size and Pin Spacing are not standard for US market (this may not be a problem for you)

3. I noted a number of problems to there tech staff about there manual being incorrect which made it very hard to get started without there test board.

4. It does email had it sending mail once every 4 hours when on vacation, time and temp, so I could see if there was any ip address changes ( non static) I would then log on to the webpage to make sure it was working using smart phone.

5. They have wifi modules that do both wired and wireless I would go this route next time.

[dhouston]

I'll add my favorite, the Lantronix XPort.

I haven't looked at these in depth for a few years. As I recall, they had email limitations. (You had to predefine the receipient. It could not handle authentication.) Has this improved?

[l_gaminde]

dhustion
I just purchased one of the http://www.connectone.com/products.asp?did=73&pid=93
37.00 not bad thanks for the tip been looking for one to play with

[Charles Linquis]

The LanReach looks like a good one.

And no - the XPORT still doesn't have decent email support. But I have a TON of code that supports it. With the help of special firmware (from GridConnect), I do things that the standard XPORT can't.

[dhouston]

I just purchased one of the http://www.connectone.com/products.asp?did=73&pid=93
37.00 not bad thanks for the tip been looking for one to play with

I probably should note a couple of gotchas.

1. The spacing of the headers is not 0.100" but 2mm (0.079") so you cannot use the $37 model in a breadboard.

2. These are 3.3V devices and the pins are not 5V tolerant. If you connect to 5V PIC input pins that have Schmitt Trigger buffers, you will need level shifters capable of handling both high and low logic levels which probably means a transistor or mosfet. 5V outputs from a PIC to the device's 3.3V inputs will also require level shifting. Here's a chart showing various logic levels.

• http://www.interfacebus.com/voltage_threshold.html

SparkFun has an inexpensive 4-channel level converter.

• http://www.sparkfun.com/commerce/pro...oducts_id=8745

You can, however, solder leads to the $38 model for testing. The pinout is given in the documentation for their evaluation board.