PWM and fade effect

[ruijc]

Hi all,

I have a question regarding PWM.
I'm using PWM to fade in/out a LED on a 12F675 with the code below.

For steps=255 TO 1 STEP -1
pwm white,steps,2
Next

I'm looking for a linear result but is not working.
When the led is almost off the speed increases ( which is obvious since the pic is using less bits to count ).

My question is, is there a workarround to minimize this effect and make the fade out/in more linear ?

Thanks

[Chris Barron]

Hi all,

I have a question regarding PWM.
I'm using PWM to fade in/out a LED on a 12F675 with the code below.

For steps=255 TO 1 STEP -1
pwm white,steps,2
Next

I'm looking for a linear result but is not working.
When the led is almost off the speed increases ( which is obvious since the pic is using less bits to count ).

My question is, is there a workarround to minimize this effect and make the fade out/in more linear ?

Thanks

I think the code is producing a linear change in PWM duty cycle. What you're perceiving as being non-linearity is probably a result of the fact that LED (and most lamps in general) brightness do not change linearly with a change in voltage.

You should actually be trying to create a logarithmic rate of change in order to produce a linear change of brightness

[sayzer]

Hi all,

I have a question regarding PWM.
I'm using PWM to fade in/out a LED on a 12F675 with the code below.

For steps=255 TO 1 STEP -1
pwm white,steps,2
Next

I'm looking for a linear result but is not working.
When the led is almost off the speed increases ( which is obvious since the pic is using less bits to count ).

My question is, is there a workarround to minimize this effect and make the fade out/in more linear ?

Thanks

Have your PWM command inside a TIMER overflow.

Like,

For steps=255 TO 1 STEP -1
TMR1IF = 0
WHILE TMR1IF = 0  
 pwm white,steps,2
WEND
Next

Thus, you get the same time of speed for each PWM step.

------------

[falingtrea]

As I understand it, your eye is a logarithmic device. So brightness changes should also be logarithmic, not linear, to be perceived correctly.

[picster]

I successfully changed apparent LED brightness just using a linear on/off duty cycle change in a loop. I believe your eye isn't registering "actual brightness" but "average brightness" (a function of time) instead, so I don't believe it's logarithmic. I would guess that the actual brightness of the LED is the same regardless of duty cycle, but the eye is doing the averaging (this could be confirmed with a scope and a phototransistor).

Actually I'm really curious about this now.

picster

[Chris Barron]

I successfully changed apparent LED brightness just using a linear on/off duty cycle change in a loop. I believe your eye isn't registering "actual brightness" but "average brightness" (a function of time) instead, so I don't believe it's logarithmic. I would guess that the actual brightness of the LED is the same regardless of duty cycle, but the eye is doing the averaging (this could be confirmed with a scope and a phototransistor).

Actually I'm really curious about this now.

picster

Yes it's curious ;-)

The eye is averaging the output brightness from the led, while at the same time it is also working on the principle of persitence of vision, POV, and the two effects combined mean there will be little hope of seeing a true linear change. It may be achievable in the long run but as soon as the observer changes their head position, or look at the led from a different angle, the flicker will be more noticeable and then the effect will not be accurate, or linear, again.

I build display devices which regularly use crossfading effects between digits and wether I use filament bulbs, neon nixie tubes or leds or VFD's, a linear voltage change always produces a non-linear change in brightness. See Youtube video as an example.

Another thing to consider too, is that as your eye sees a light source which has an increasing brightness it reacts by closing down the iris and therefore it 'spoils' the effect you thought you were going to see, but we all experience this effect 'similarly' and are accustomed to it.

The code posted in the first message should run 'linearly' no matter what the PWM duty cycle is set at, because even with a small on time the PWM routine should be padding the rest of the time period with a respective amount of offtime to produce a fixed PWM period

Chris

[Acetronics2]

Hi,

May be you should add the PWM output, without any filtering it is totally "random" ( short way of saying it ...) as a signal ... so ...

is it really the correct way to achieve a decent "linear" fading ... ???

...

Alain