Darrel's interrupts in a 7 segment display

[EarlyBird2]

Hi all,
I'm having trouble understanding something in this example code. Maybe someone can explain.

Main:
  FOR Value = 0 TO 999
    GOSUB SetDisp
    PAUSE 500
  NEXT Value
GOTO Main

'---[Set 7-seg patterns to WORD value]--------------------------------------
SetDisp:
  FOR Idx = 2 to 0 STEP -1
    Temp = Value DIG Idx
    LookUp Temp,[132,175,193,137,170,152,144,143,128,136,210,251],Temp
    SEGDEF(Idx) = Temp
  NEXT Idx
RETURN

The biggest question is why is there 12 data points in the table? I am assuming that the actual numbers are because of the wiring of the digits with this specific LED as I can not figure out a segment pattern. After that, I fall down on why 12 instead of 8 unless it involves positioning the decimal point somehow. I wonder, if with the original wiring, this would be clearer to me. I would think that you would line up the segments in order with the port pins in order.

Thanks
Mark

As I can not resist a challenge even if it is only an academic exercise to me.

------- GFEDCBA

0 132 10000100
1 175 10101111
2 193 11000001
3 137 10001001
4 170 10101010
5 152 10011000
6 144 10010000
7 143 10001111
8 128 10000000
9 136 10001000
F 210 11010010
- 251 11111011


Looking at the bit pattern for :-

0 the active segments are 0 and inactive 1 in a 0 the central cross bar is inactive therefore this is C
6 the only inactive segment is top right therefore this is E
5 the inactive segments are top right and bottom left so bottom left is D
9 confirms bottom left is D
3 top left and bottom left inactive so top left is A
2 top left and bottom right inactive so bottom right is G
7 top left centre bottom left and bottom inactive so bottom is B

which leaves F is the top segment giving this pattern

-F-
A E
-C-
D G
-B-


251 is the centre bar obviously used for - (minus)
210 converting the bit pattern gives F

Having decoded this pattern it makes no sense to me as the normal segment pattern is



Leaving the question why connect a 7 segment display in this no standard way?

[Dave]

Well Actually Steve, The display's may have been wired that way in the schematic originally. Makes no difference. As far as the table is concerned, to generate all 16 hexidecimal characters the table would be 16 entries wide. in the past I have generated tables with all 16 entries as well as lower case "c,n o r". Thats 20. Ther is no standard way if you get my drift. It's completely up to the circuit designer.

[EarlyBird2]

Well Actually Steve, The display's may have been wired that way in the schematic originally. Makes no difference. As far as the table is concerned, to generate all 16 hexidecimal characters the table would be 16 entries wide. in the past I have generated tables with all 16 entries as well as lower case "c,n o r". Thats 20. Ther is no standard way if you get my drift. It's completely up to the circuit designer.

In my post I decoded the lookup table to work out the display pattern and the wiring. I intuitively did not like the resultant pattern and wondered why choose that pattern. Internet searches revealed a commonly followed trend of port.0-port.7 connected to a-g respectively.

From Wikipedia

LED-based 7-segment display which cycles through the common glyphs of the ten decimal numerals and the six hexadecimal "letter digits" (A–F)
Hexadecimal digits can be displayed on seven-segment displays. A combination of uppercase and lowercase letters is used for A–F;[6] this is done to obtain a unique, unambiguous shape for each hexadecimal digit (otherwise, a capital D would look identical to an 0 and a capital B would look identical to an 8). Also the digit 6 must be displayed with the top bar lit to avoid ambiguity with the letter b.

Which implies that there are two ways to wire up a seven segment display one for g-a encoding and one for a-g encoding. But as you say no one has to follow these commonly used encodings, which do dictate the circuit to be used.

The inclusion of "-" and "F" in the encoding makes me think that the original code was probably for displaying temperatures. Also the codes are eight digits which includes the DP reinforcing the idea of a temperature display. I wonder if the original project was wired in the same way, that is assuming this is recycled code.

Can anyone see any advantage in this scheme?

-F-
A E
-C-
D G
-B-

I can not and surely the wiring will be like spaghetti.