16F877 elapsed time control

[BerkayT]

how can i start the timer for example when the analog input from the pot is 3 V and stop the timer when it is 5 V ?

thanks

[mackrackit]

loop:
If pot value => 3V then time
goto loop

time:
for X = 1 to 255
pauseus 10
t = t + 1
do whatever, pot
if pot value =  5V then tCalc
next x
tCalc:
display t
goto time

You may want to consider using ADCIN in place of POT.
Notice I changed the example to PAUSEUS.
And someplace around here there is a discussion about code execution time, or just test it to adjust the PAUSEUS.

[BerkayT]

Thanks for your idea,

One more question. How am i gonna define the voltage. I have added a loop like but it didnt work. What can be the problem ?

ADC_READ:

ADCIN 0, ADCINFO
D=ADCINFO*100/51

timeloop:
if D>3 then
T1CON.0=1
if D>=4 then
T1CON.0=0
endif
ELSE
goto timeloop
endif

[mackrackit]

First off the ADC needs setup, here is an example.
http://www.microengineeringlabs.com/...pbp/adcin8.bas

Voltage...
Lets say you are using an 8 bit ADC. Voltage reference is VDD and the PIC is running at 5 volts.
There are 256 steps, 0 to 255.
The ADC value of 255 will represent full scale and be 5 volts.
The ADC value of 127 will represent 2.5 volts.
Looking for 3 volts? The ADC vale would be 153.
Want more accuracy? The 10 bit ADC has 1024 steps.

Your loop. After the set up.

loop: 	
ADCIN 0, adval				' Read channel 0 to adval
IF adval <= 153 then gosub Xlabel    '3 volt and less trigger
IF adval = 255 then gosub Zlabel    '5 volt trigger	    
Pause 100       				' Wait .1 second
Goto loop       				' Do it forever

Xlabel:
'Do something
Return

Zlabel:
'Do someting
Return
End

That is the basics.

[BerkayT]

thanks alot
another newbie question
can i use tmrcon istead of for loop
such as;

CalcTime var word
Define LCD_DREG PORTC
Define LCD_DBIT 4
Define LCD_RSREG PORTB
Define LCD_RSBIT 0
Define LCD_EREG PORTB
Define LCD_EBIT 2
DEFINE LCD_BITS 4
DEFINE LCD_LINES 2

DEFINE ADC_BITS 10
DEFINE ADC_CLOCK 3
DEFINE ADC_SAMPLEUS 50

TRISA = %11111111 ' Set PORTA to all input
ADCON1 = %00000000 ' Set PORTA analog

ADCINFO VAR BYTE


'================================================= =======================

T1CON.0=0
TMR1H = 0
TMR1L = 0
ADCON1 = 0


ADC_READ:
PAUSE 500

timeloop:
ADCIN 0, ADCINFO
IF ADCINFO => 511 THEN GOSUB STARTTIMER
IF ADCINFO == 980 THEN GOSUB STOPTIMER
PAUSE 100
GOTO timeloop

STARTTIMER:
T1CON.0=1
RETURN

STOPTIMER:
T1CON.0=0
RETURN

GOTO ADC_READ

CLEARWDT
CalcTime.Highbyte=TMR1H
CalcTime.Lowbyte=TMR1L

Loope:
LCDOUT $FE, 1
LCDOUT "t:", CalcTime
Pause 500
Goto loope

GOTO ADC_READ
END

[mister_e]

euh yeah, but the above will never do something else than reading the ADCs?

What do you want to do exactly?

[BerkayT]

euh yeah, but the above will never do something else than reading the ADCs?

What do you want to do exactly?

hmm i want it to read the adc s and there will be a voltage change from 2.5 v to 4.8 V my aim is to measure the time elapsed between 4.8 and 2.5 volts and write it to lcd

thanks alot for helping

[BerkayT]

Hi mackrackit

i tried this

loop:
If pot value => 3V then time
goto loop

time:
for X = 1 to 255
pauseus 10
t = t + 1
do whatever, pot
if pot value =  5V then tCalc
next x
tCalc:
display t
goto time

You may want to consider using ADCIN in place of POT.
Notice I changed the example to PAUSEUS.
And someplace around here there is a discussion about code execution time, or just test it to adjust the PAUSEUS.

but it doesnt stop counting for a defined voltage once it is triggered it does not stop for the final voltage.

loop:

adcin 0, adval

If adval => 500 then time
goto loop

time:
for X = 1 to 1023
pauseus 10
t = t + 1
If adval = 1000 then tcalc
next x


tCalc:
LCDOUT $fe, 2,"Time" ,":",DEC t
goto time

Once i stop it i ll adjust the pauseus value
Anything missing? any suggestions?

[mackrackit]

You may want to explore the WHILE-WEND command.