16f88 to parallax 2x16 lcd

[rdxbam]

should this code work to get the parallax to display a string?




'===============================
'' pic16f88

INCLUDE "modedefs.bas"


'DEFINE OSC 10 ' 4MHz doesn't work try others

TRISB = %00000000 ' PORTB all outputs
ADCON1 = %00000111 ' Disable A/D converter
ANSEL = %00000000 ' all analog pins to digital

'================================

PinOut VAR PORTB.5 ' Tx on RB5
Led3On VAR PORTB.3 ' turn on LED if Tx

'================================

BAUD con 16780 ' 2400 Baud, inverted, NoParity: conservative for testing

'================================
PinOut = 0 ' set to a norm state
PAUSE 100 ' a little wait time

HIGH PinOut
HIGH Led3On

Pause 5000 ' LCD start up delay
SEROUT2 PinOut, BAUD,["STR-1 012345678",13,10]
LOW Led3On
PAUSE 5000

'================================

Loop:

HIGH Led3On
SEROUT2 PinOut, BAUD, ["STR-2 012345678",13,10]
PAUSE 5000
LOW Led3On
SEROUT2 PinOut, BAUD, ["STR-3 012345678",13,10]
goto Loop

END

[mackrackit]

No, you are missing a bit here and there. Serial LCDs have their own command set. I went to this page and think these are the ones for you.
http://www.parallax.com/Store/Access...%2cProductName

LcdBkSpc        CON     $08             ' move cursor left
LcdRt           CON     $09             ' move cursor right
LcdLF           CON     $0A             ' move cursor down 1 line
LcdCls          CON     $0C             ' clear LCD (use PAUSE 5 after)
LcdCR           CON     $0D             ' move pos 0 of next line
LcdBLon         CON     $11             ' backlight on
LcdBLoff        CON     $12             ' backlight off
LcdOff          CON     $15             ' LCD off
LcdOn1          CON     $16             ' LCD on; cursor off, blink off
LcdOn2          CON     $17             ' LCD on; cursor off, blink on
LcdOn3          CON     $18             ' LCD on; cursor on, blink off
LcdOn4          CON     $19             ' LCD on; cursor on, blink on
LcdLine1        CON     $80             ' move to line 1, column 0
LcdLine2        CON     $94             ' move to line 2, column 0
LcdCC0          CON     $F8             ' define custom char 0
LcdCC1          CON     $F9             ' define custom char 1
LcdCC2          CON     $FA             ' define custom char 2
LcdCC3          CON     $FB             ' define custom char 3
LcdCC4          CON     $FC             ' define custom char 4
LcdCC5          CON     $FD             ' define custom char 5
LcdCC6          CON     $FE             ' define custom char 6
LcdCC7          CON     $FF             ' define custom char 7

This should work.

SEROUT2 PinOut, BAUD,[LcdBLoff, LcdOn1, LcdCls]
SEROUT2 PinOut, BAUD,["HELLO WORLD"]

Try a test program with all of the above.

[rdxbam]

thanks for the tip. i dl'd two of the code samples from that page, mixed and matched and it still didn't work. i looked too at the melabs pages for the diff's of BS2 and PBP, just in case. but i did get it to work ,,,

0. without setting the values for these, OSC and OSCCON, could not get anything written to the LCD. i set them for 8MHz, as 4MHz would not work. so i looked at section 4.6.1 of the datasheet and set the following...

DEFINE OSC 8
OSCCON= %01110100 ' internal RTC Oscillator freq select
' [bits 6-4 = 8MHz], [bit 2] INTOSC freq stable bit set

1. configuration was set as HS, WDT_ON, PWRT_ON, BOD_ON, MCLR_OFF, PROTECT_OFF

2. the baud rate set using these values, "396 or 16780" didn't work for me. but t2400 does.

thanks for your help!!!!

[mackrackit]

I do not have the same LCD as you have to test, so I am not positive the commands are correct.

BUT...I now see some other problems.
First, with out changing any of your settings make an LED blink at say one second on and one second off and see if the timing is correct.

LOOP:
HIGH PORT?.?
PAUSE 1000
LOW PORT?.?
PAUSE 1000
GOTO LOOP

When you see it is not, here is why.
In your config settings HS is for an external OSC, you need "_INTRC_IO"

Wait a minute ... Did you get it working???

2. the baud rate set using these values, "396 or 16780" didn't work for me. but t2400 does.

[rdxbam]

yes, i did get it to work. and yes, i am able to get a LED to blink from PORTB.3 and get string of char's to display on the LCD now.

and, this is whether i set INTRC_OSC or EXTRC_OSC. although i am not using an external OSC!

for my current code, at least from the process of elimination, having these two values, "DEFINE OSC x" and "OSCCON= x" set correctly made the difference along with the baud rate.

thanks!

[rdxbam]

Hey Mackrackit,

forgot to mention this...SEROUT2 vs SEROUT. i.e., SEROUT2 didn't work for me. once i switched to SEROUT, along with the other modifications, it has worked well. looks like some diff with the "true" or "inverted" mods with baud?? as i'm new to this hard to say for sure...

thanks!

[mackrackit]

Hey Mackrackit,

forgot to mention this...SEROUT2 vs SEROUT. i.e., SEROUT2 didn't work for me. once i switched to SEROUT, along with the other modifications, it has worked well. looks like some diff with the "true" or "inverted" mods with baud?? as i'm new to this hard to say for sure...

thanks!

Just for fun now that it is working, try the SEROUT2 again.
SEROUT is 8N1 so SEROUT2 396 should work. But maybe that is why MELABS has SEROUT so it works with Stamp stuff??