Old classic If-Then...

[Acetronics2]

Hi, Ioannis

Why not use an AND combination of your conditions.

Karnaugh would LOVE your example.

Try this little soft ... and ENJOY.

Karnaugh Minimizer 2.0
Copyright (c) 2002-2007 ShurikSoft.
http://www.shuriksoft.com

Alain

[Ioannis]

Hi all and thanks for the replies.

Alain: I tried with AND but got an error of too many variables. Indeed was long line!

Melanie: That was what I did just before reading your post. Yes this works but was not appealing to me as an elegant solution.

Steve & Tobias: Yes,I see now, after the morning cup of coffee that it never reached the ELSE statement.

Thanks again to all.

Ioannis

[Acetronics2]

Hi Ioannis

I do not Understand you ...

'Essai 16F84 Random

DEFINE LCD_EBIT 1                          ' Other LCD pins are same as Manual - Holy Manual - my sweet Manual ...

'   DEFINE LCD_DREG PORTB               ' I/O port where LCD is connected
'   DEFINE LCD_DBIT 0
'   DEFINE LCD_RSREG PORTB
'   DEFINE LCD_RSBIT 4                  ' Register select pin
'   DEFINE LCD_EREG PORTB
'   DEFINE LCD_EBIT 5                   ' Enable pin
'   DEFINE LCD_BITS 4                   ' 4-bit data bus
'   DEFINE LCD_LINES 2                  ' LCD has 2 character lines
 
   DEFINE OSC 4
   
@	__config _XT_OSC & _WDT_ON & _CP_OFF

'*****************************************************************************
'Variables

Level 	   		var Word
High_Level 		var Word

Onboard_an2		var Word
PressLimit 		var Word

Auto1			var Bit
Thermikol 		var Bit
Thermistor1		var Bit
Pump			var Bit

LevelOk			var Bit
PressOk			var Bit

module_rel_out	var Portb.7

'*****************************************************************************
'Constantes

'*****************************************************************************
'Preset

CLEAR

PORTA = 0
PORTB = 0

TRISA = 0
TRISB = 0

High_Level 	= 40000
Level		= 0
Thermikol   = 1
Thermistor1	= 1
Onboard_an2 = 500
PressLimit 	= 35000

Auto1		= 1
Pump		= 0



PAUSE 500

LCDOUT $FE,1

RANDOM Level
RANDOM Onboard_An2

Loop:

RANDOM Level
RANDOM Onboard_An2

IF (level <= high_Level) THEN
 	PORTB.5 = 1
ELSE
  	PORTB.5 = 0
ENDIF

IF ( onboard_an2 <= PressLimit ) THEN
 	PORTB.6 = 1
ELSE
  	PORTB.6 = 0
ENDIF

Module_rel_out =  (level <= high_Level) && Thermikol && Thermistor1 && Auto1 && ( onboard_an2 <= PressLimit ) && !Pump  

LCDOUT $FE,2,# Module_Rel_Out ,"   ",DEC5 Level ," ",DEC5 Onboard_an2 ,"  "
LCDOUT $FE,$C0,"out", DEC5 High_Level, " ", DEC5 Presslimit 

PAUSE 300

IF Module_rel_out THEN PAUSE 500

GOTO Loop

END

As you see ... I played somewhat with my Personnal Testboard to verify everything was running fine ...

And it runs fine !!!

"your" line is here :

Module_rel_out =  (level <= high_Level) && Thermikol && Thermistor1 && Auto1 && ( onboard_an2 <= PressLimit ) && !Pump

...

Value Comparisons or logic levels have equal behaviour here ...

Cheers ...

Alain

[Ioannis]

Hi Alain.

On the following if I try to put the second if-then inside the logic expression, I get an "Temp variables exceeding T4" error in MPASM assembler.

This compiles OK:

if pump=0 and (thermistor1=1 or thermiko1=1 or onboard_an2>(pres_limit+10)) then 
	module_rel_out.0=0
endif


if level>stop_level then
	if pump=0 then
		module_rel_out.0=0
	endif
endif

This produces the above error:

if pump=0 and (thermistor1=1 or thermiko1=1 or onboard_an2>(pres_limit+10) or level>stop_level) then 
	module_rel_out.0=0
endif

Thanks,
Ioannis

[Acetronics2]

Hi, Ioannis

Do not use " IF thermistor1 = 1" but "IF Thermistor" ... result is the same

Do not use " IF thermistor1 = 0 " but "IF NOT Thermistor" ... result is the same

Alain

[Acetronics2]

if  (pump=0) and ( thermistor1 or thermiko1 or ( onboard_an2>(pres_limit + 10))) then 
	module_rel_out.0=0
endif


if (level>stop_level) then
	if pump=0 then
		module_rel_out.0=0
	endif
endif

Compile fine

BUUUUUUT ... I do think you should make your Karnaugh Table ( Table of states ) "a bit" clearer ... might help a lot ( lol )

Alain

Alain

[Archangel]

Thanks Alain,
For

RANDOM Level
RANDOM Onboard_An2

It gives me a new test tool, never could see a use for that command before. Sometimes it's not the main point of your posting that benefits others, sometimes it's the little things that you use everyday.

[Archangel]

Hi, Ioannis

Do not use " IF thermistor1 = 1" but "IF Thermistor" ... result is the same

Do not use " IF thermistor1 = 0 " but "IF NOT Thermistor" ... result is the same

Alain

Could you please explain a little more, so I can understand why ?
Thank You

[mister_e]

I understand why.. the problem is to explain... enjoy the following language barrier mess

If ConditionIsTrue Then DoSomething

Dealing with Bit Var, you have ONLY 2 choices... OR the var is 1 OR the var 0, True or False.

So why messing with condition if your variable already hold it?

It's just another way to write your IF-THEN

[Darrel Taylor]

I get an "Temp variables exceeding T4" error in MPASM assembler.

Hi Ioannis,

That error is comming from ReEnterPBP.bas

There's no way for it to know if the complex formula/IF statement is in the main program or the interrupt handler. And if it's in the handler, it will end up overwriting PBP's system vars.

If you know for sure that the offending statements are NOT in the handler. You can open the ReEnterPBP.bas file and comment the error line.

        ifdef T5
;            ERROR "Temp variables exceeding T4"
        endif

HTH,

[Archangel]

Hi Ioannis,

That error is comming from ReEnterPBP.bas

There's no way for it to know if the complex formula/IF statement is in the main program or the interrupt handler. And if it's in the handler, it will end up overwriting PBP's system vars.

If you know for sure that the offending statements are NOT in the handler. You can open the ReEnterPBP.bas file and comment the error line.

        ifdef T5
;            ERROR "Temp variables exceeding T4"
        endif

HTH,

Hi Darrel,
So if I understand this right, ERROR is a reserved word in assembler, and if IFDEF calls it then MPASM displays the error when compiling . . . YES?<br><br> Hi Steve, thanks , I will give that some thought.

[Darrel Taylor]

Hi Darrel,
So if I understand this right, ERROR is a reserved word in assembler, and if IFDEF calls it then MPASM displays the error when compiling . . . YES?

Yup. You got it.