Printable View
Hello
I need som help with this program.
It should work like this: when power on, GPIO.2 is high. When I apply HI on GPIO.0, after 3 sec GPIO.2 should be low. Config is mclr=off, pwrt=on, wdte=on,boren=on, int OSC I/O.
Here is the code
CMCON=7
ul var GPIO.0 'Define GPIO.0 pin as ul
izl VAR GPIO.2 'Define GPIO.2 pin as izl
High izl
Input ul
loop:
if ul=1 then
pause 3000
low izl
end if
goto loop
Does 'blinky LED' work?
I'm sorry, but I can't find 'blinky LED' example.Quote:
Originally Posted by skimask
http://www.melabs.com/resources/samples.htm#proCode:' Example program from manual to blink an LED connected to PORTB.0 about once a second
loop: High 0 ' Turn on LED connected to PORTB.0
Pause 500 ' Delay for .5 seconds
Low 0 ' Turn off LED connected to PORTB.0
Pause 500 ' Delay for .5 seconds
Goto loop ' Go back to loop and blink LED forever
End
Hope this helps..
WOW!!!!!!!Quote:
Originally Posted by rele
I know its tough, but count to ten, take deep breaths and read Mels most http://www.picbasic.co.uk/forum/show...99&postcount=1Quote:
Originally Posted by skimask
If you look at his code, there is some logic in his thinking, he has made an attempt to write a program, which doesn't work, and thus came here seeking assistance...
Hi,
First of all let's leave guns and knives outside ...
Won't you think a little ( real ! ) SCHEME would be compulsory, here ???
just to verify how and what to inputs and outputs are linked ...
"my two cents"
Alain
I need to disable writing to external eeprom few secconds after power is applyed. So, GPIO.2 pin is connected to the WP pin of eeprom, and GPIO.0 pin have +5V when eeprom have +5V. Between VCC and MCLR is 4K7.
I know this is very simply for most of you, but this is my first program, and it has practical purpose.
Regards
I think the point that skimask was trying to get over, is that for a 1st program, the main goal is to get the chip to flash a LED correctly, then go on to develope that.
A golden rule here is to look at the datasheet, and then set the pic up accordingly. Often these small chips don't have their pins set to digital i/o by default, so need the config set accordingly.
Once you have a bit of code that blinks an LED, then introduce inputs and modify the code to get the result you want.
Hi,Quote:
Originally Posted by rele
NOOOOOO ... nothing is simple !!!
We still do not know what is connected to your Pic I/Os ...
Just remember if hardware is False ... software can't work as expected !!! ... and vice versa.
We must know everything of your project, if you want us to give a serious answer.
Now, for some fun ...
You ask for help...Ok, but you do not tell us even if it works ... How do you verify GPIO.2 works ( or doesn't work ! ) properly ???
How do you drive GPIO.0 ???
For the day,We do not use the crystal ball on this Forum ... so, you must do your "part of the work" of debugging, and tell us what's on your side ...
Alain
Pin1 - +5VQuote:
Originally Posted by Acetronics
Pin2 - N/C
Pin3 - N/C
Pin4 - +5V thru 4K7
Pin5 - Output pin
Pin6 - N/C
Pin7 - Input pin
Pin8 - GND
Output pin is connected directly to WP pin of external eeprom. Input pin is connected directly to VCC pin of external eeprom. Purpose of program is to disable writing to external eeprom for 3 secconds after power is applyed to eeprom.
I verify condition of GPIO.2 with logic probe.
Regards
Hi,
Just a little innocent question ...
Does your program compile ???
...
Alain
Program is ok, I have one mistake in hardware. I put one resistor 10K between input pin and GND and now it is ok.
Thank you for your help.
Regards
Curious as to why you want to connect WP and disable writing for 3 seconds.Quote:
Originally Posted by rele
Is it to be extra double super sure that the eeprom doesn't get written to?
Hi,
Quote:
Just a little innocent question ...
Does your program compile ???
You sure ??? just a Typo, I wonder ...Code:
CMCON=7
ul var GPIO.0 'Define GPIO.0 pin as ul
izl VAR GPIO.2 'Define GPIO.2 pin as izl
High izl
Input ul
loop:
if ul=1 then
pause 3000
low izl
end if ... sure about the spelling ???
goto loop
Now, connecting GPIO.0 to +5v would have been so simpler to find there were NO problem in your code ...
Do not tell us you have two separate 5v supplies ...
Alain
Yes I have two separate +5V. It is for coded caraudio. When I reprogram eeprom for immo off and connect +5V to WP pin of eeprom carradio is working but memory station is not working, also settings for audio dont work, all data that are usualy stored to eeprom.
I need to disable writing just for first few secconds when MCU is checking one location in e2prom.
My mistakeQuote:
Originally Posted by Acetronics