Printable View
Hi,
I search the Best way to save RFID Data !
Did some one have experience what I should use EEprom or something else.
I Try with 24C08 but the problem is that I have a adress byte but how this can work when I go for example to adress 512 this is more then a byte.
Adress var byte
Adress = 512 but this is not byte anymore
I2CWrite sda,scl,%10101000,Adress,[$00,$16,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$0 0,$00,$00,$00]
Thanks for any example.
Regards Pesti
Then I suppose your address might magically become a WORD just like the good book says in the I2CWrite section...and I quote:Quote:
Originally Posted by Pesticida
The Address size sent (byte or word) is determined by the size of the variable that is used. If a byte-sized variable is used for the Address, an 8-bit address is sent. If a word-sized variable is used, a 16-bit address is sent. Be sure to use the proper sized variable for the device you wish to communicate with. Constants should not be used for the Address as the size can vary dependent on the size of the constant. Also, expressions should not be used as they can cause an improper Address size to be sent.
Hi,
Thank you !
I understand what you mean but on the PDF File for the 24C08 they says that the adress is just a byte and not a word.
Now my question is how can I write for example on adress 512 or 700 when I can just use a byte adress and not a word.
For the 24c02 and 24c01 I dont have Problems but when I need more then 256 bytes I can not read or write.
Can I use this I2CWrite sda,scl,$A9,here >512<here,[Tmp_Data]
Thanks
Regards Pesti
Ok!
I found that the 24C08 have 2 Blocks but thats mean that each block have 512 Bytes!
how can I read or write the first block or the second!?
I have just a byte adress!
regards Pesti
Now the answer you want is in the I2CREAD section instead of the I2CWRITE, which, incidentally, goes hand in hand with I2CREAD, because to I2CREAD something, first you have to I2CWRITE something, unless you would rather I2CREAD an empty chip, which isn't really empty, but full of no data, and sometimes no data is better than some data, either of which can be I2CREAD quite effectively, and either of which can be I2CWRITTEN over to replace either the no data or the some data which will be I2CREAD later on.Quote:
Originally Posted by Pesticida
Thats mean i must use something like this:
EraseEEprom= $A8
EEprom_Block = 0
Tmp_Daten = $00
EraseEEprom:
Erase_Loop:
for NextAdr = 0 to 255
I2CWrite sda,scl,EEprom_Adresse,NextAdr,[Tmp_Daten]
pause 10
Sound Buzzer,[122,1]
next NextAdr
EEprom_Adresse = EEprom_Adresse + 2
EEprom_Block = EEprom_Block + 1
if EEprom_Block => 4 then EEprom_Block = 0 : goto Exit_Loop2
goto Erase_Loop
Exit_Loop2:
Sound Buzzer,[122,250]
goto Main
Regards pesti
Make it easy on yourself, get a 24C256, 32k x 8 eeprom. Word address, byte data
I2Cwrite datapin, clockpin, $a0, address, data
But if you're hellbent on using the 24c08...
address var word 'only use lower 10 bit
addr var byte
control var byte
addr = address.lowbyte
control = $a0 + ( address.highbyte << 2 )
i2cwrite datapin, clockpin, control, address, data-whatever
OK,
I must write this :
Control = $A1
For address = 0 to 1023
addr = address.lowbyte
control = $a0 + ( address.highbyte << 2 )
I2CRead sda, scl,Control, addr,[EEprom_Daten[Byte_Count]]
Pause 10
Byte_Count = Byte_Count + 1
if Byte_Count > 15 then
Byte_Count = 0
HSEROUT [DEC3 NextAdr-15, ": ",HEX2 EEprom_Daten[0],HEX2 EEprom_Daten[1],HEX2 EEprom_Daten[2],HEX2 EEprom_Daten[3],HEX2 EEprom_Daten[4],HEX2 EEprom_Daten[5],HEX2 EEprom_Daten[6],HEX2 EEprom_Daten[7],DEC2 EEprom_Daten[8],DEC2 EEprom_Daten[9],DEC2 EEprom_Daten[10],DEC2 EEprom_Daten[11],DEC2 EEprom_Daten[12],DEC2 EEprom_Daten[13],HEX2 EEprom_Daten[14],HEX2 EEprom_Daten[15],13,10]
endif
next address
Or I make again a mistake ?!
Regards Pesti
I don't know. Does it work?Quote:
Originally Posted by Pesticida
If it does, then you didn't make a mistake.
If it doesn't, then there must be a flaw in your logic.
Hi
No this dont work!
My chip have the Pin E2 to VCC thats mean The Device Adress is :10101000 for Write and
10101001 For Reading.
I try all combination but dont work.
Regards Pesti
Ok, is it the serial part that's not working?Quote:
Originally Posted by Pesticida
The EEPROM is returning bad data?
Is the program running?
Which is it?
Think simple...build it up...
Make the LED blink...Show some data on the LED...Make the HSEROUT work
I know you don't have an LED here...maybe you should put one there eh?
Hi,
im so Stupid I forgott something important ,on the Chip I forgott to set WC Low,and i use now more pause to write and to read data.
Now is working but what i don't understand ,on the 24C02 i dont set wc too and has working!
What you think is this a good Idea to use 24c chips to store rfid tags data,the chips have a 1000.000 write cyclus.
When I write on one day Double (Write and Erase) I have then on one Day maybe 4 Write Cycle.
Thank You
Regards Pesti
depending the warranty and service you want to provide... but you could use F-RAM instead
not bad ;)Quote:
Originally Posted by FM24C04A datasheet
Thank You Mister_e
The RFID Data will be stored on the 24C and then Send trough GPRS Transmitter to Central Unit.
If all is ok the data will be Erased.
And I have again free space for new data.
Regards Pesti
Ok
All work fine now but :-)
I receive the data from rfid reader in ascii i use to receive data on the pic this:
Serin2 PortD.0,84,[Wait("E0") ,Daten[6],Daten[5],Daten[4],Daten[3],Daten[2],Daten[1],Daten[0]]
Daten[7] = $E0
but when I send to pc and to LCD with this
HSEROUT [hex2 Daten[7],hex2 Daten[6],hex2 Daten[5],hex2 Daten[4],hex2 Daten[3],hex2 Daten[2],hex2 Daten[1],hex2 Daten[0],13,10]
Lcdout $fe,$80,hex2 Daten[7],hex2 Daten[6],hex2 Daten[5],hex2 Daten[4],hex2 Daten[3],hex2 Daten[2],hex2 Daten[1],hex2 Daten[0]
I receive on the PC and on the LCD this : E030343031303030
I don't have found the way to convert to hex I need Hex on PC and on LCD.
Thanks
Regards Pesti
Have you opened your PicBasicPro manual since you bought PicBasicPro?Quote:
Originally Posted by Pesticida
What do you think the HEX2 does FOR you?
Take the HEX2 out of your HSEROUT and you'll get raw data.
Hi
Yes I read the book and i now that hex is to convert decimal in hex !
I think i have a serial problem i have read more rfid chips and i receive always the same serial.
Thank you
Regards Pesti
Hi
Yes I now what is happen the rfid send ascii,the pic receive the ascii and convert all the characters in decimal values 0 is 30 ,4 is 34 and so on.
Than I have more than 8 bytes I have 16 bytes.
I must now convert the decimals in hex,while i need hex data.
I try with hex but dont work!
Regards Pesti
Re-Read Post #16...then refer to your PBP on the proper use of SERIN/SEROUT/(etc) available modifiers and you WILL have your answer. I understand what you want, but I'm not going to give you the answer you need because you have all of the resources you need to get that answer...and you might learn something.Quote:
Originally Posted by Pesticida
Sorry Skimask!
When I have 30 34 30 31 thats mean i need a modifier with 4 to have 04 and 01.
Regards Pesti
Yes, I know...and your answer awaits...Quote:
Originally Posted by Pesticida
Hi,:-)
I Use this:
DEBUGIN [WAIT("E0"),dec4 Daten[14], dec4 Daten[13], dec4 Daten[12], dec4 Daten[11], dec4 Daten[10], dec4 Daten[9], dec4 Daten[8],dec4 Daten[7], dec4 Daten[6], dec4 Daten[5], dec4 Daten[4], dec4 Daten[3], dec4 Daten[2], dec4 Daten[1],dec4 Daten[0]]
While DEBUGIN more fast is,but i have now more bytes this is not what I want.
And that with Raw data what you have mean is working: :-)
HSEROUT ["E0",Daten[14], Daten[13],Daten[12], Daten[11], Daten[10], Daten[9], Daten[8], Daten[7], Daten[6], Daten[5], Daten[4], Daten[3], Daten[2], Daten[1],Daten[0],13,10]
What is if I use instead dec4 hex modifier,can I reduce my bytes!?
Thank you Skimask
Regards Pesti
This is the Solution :-)
DEBUGIN [WAIT("E0"),Daten[13],Daten[12],Daten[11], Daten[10], Daten[9],Daten[8], Daten[7],Daten[6], Daten[5], Daten[4], Daten[3], Daten[2], Daten[1], Daten[0]]
Pause 50
for N = 13 to 1 step - 2
Daten[N]= ((Daten[N]-$30) *10) + (Daten[N-1]-$30)
Pause 5
next N
High Led_Tag
Gosub ReadTime
Gosub Read_BCD
HSEROUT ["E0",hex2 Daten[13],hex2 Daten[11],hex2 Daten[9],hex2 Daten[7],hex2 Daten[5],hex2 Daten[3],hex2 Daten[1],13,10]
Regards Pesti
That wasn't quite the solution I was going for, but what you've got will work just fine.
One thiing to note...in the first line below:
You might want to put in some code for checking an out-of-bounds condition.Quote:
Originally Posted by Pesticida
Hi Skimask,
What you mean with out of bond!?
Did you mean when I receive a wrong character.
Regards Pesti
What happens if you get a character that you weren't expecting? One with a value too low or too high...Quote:
Originally Posted by Pesticida
For instance:
Daten[N]= ((Daten[N]-$30) *10) + (Daten[N-1]-$30)
What happens if the value in 'Daten[N]' or 'Daten[N-1] is $30? is $20? is $0?
Hi,
Ok this is a very good argument ! :-)
Is good that you have warnning me I forgot this :-(
I think that i should the Data discard !
Or I think wrong !?
Something like this:
Bad_Data var bit
Bad_Data = 0
Data_Check:
for N = 0 to 13
If Daten(N) < $30 then Bad_Data = 1 : Daten(N) = $30
Next N
Select case Bad_Data
case 0 ' it's all ok
for N = 13 to 1 step - 2
Daten[N]= ((Daten[N]-$30) *10) + (Daten[N-1]-$30)
Pause 5
next N
case 1 ' no good :-)
Bad_Data = 0
Goto Warning or something like that
end select
If I have Daten[N] = $30 this is not bad while $30-$30 = 0
Regards Pesti