-
12F675 cant serout to PC
Hi all,
I have here a 12F675 and i was using it read a LM35 and send out temp to PC via serial port ( not using MAX232 ).
The problem is that i'm facing comunication problems.
I cant get the pic to send a correct word out !
All i get is rubbish.
I've seen someone here with the same problem but it was resolved with XT->HS change !
I've tryed so many things ( speed, xtals, etc ) and nothing works :(
Here's the code:
@ DEVICE PIC12F675, MCLR_ON
' Master Clear Options (Internal)
@ DEVICE PIC12F675, PROTECT_OFF
' Program Code Protection
define osc 4
Include "modedefs.bas" ' Include serial modes
define osc 4
ANSEL = %00000000 ' Set analog ports to digital mode
CMCON = %00000111 ' Turn off comparator
'TRISIO = 00001000 ' designate gpio.0,1,2,4,5 as output 3 as input
WPU = %00000000 ' Disable pull-ups
TRISIO = %00000 ' Set all I/O's to outputs
out:
low gpio.2
Serout2 GPIO.1,396,["396",10,13] ' check if this works
pause 200
Serout2 GPIO.1,84,["84",10,13] ' or this
pause 200
Serout2 GPIO.1,188,["188",10,13] ' or this
pause 200
Serout2 GPIO.1,16572,["16572",10,13] ' or this
pause 200
Serout2 GPIO.1,N2400,["N2400",10,13] ' or this
pause 200
high gpio.2
pause 500
Goto out
thanks for the help
.
-
add that line at the top of your code
this should help
-
Thanks for the tip Mister-e
but isnt this for when using only the internal osc ?
i'm using an external 4Mhz xtal
.
-
Yup and i missed it...
What capacitor value did you put on your Crystal? 15-22pf?
what happen if you remove the MAX232, and use inverted mode for your baudrate???
With the MCLR_ON, it mean you use MCLR, so i hope this pin is tied to Vcc?
Clean psu, decoupling caps here and there?
Did you also tried with the internal OSC?
I don't see anything wrong in the code...
-
I have tryed that but if i use that line it does not work ( doesnt send data nor the led in gpio.2 blinks )
.
-
what happen if you change MCLR_ON to MCLR_OFF?
Are you sure it's a 4MHZ crystal?
Can you measure it with a scope?
-
I'm not using any Max232
About the MCLR, when on i hooked it to vdd, also tryed off and result is the same.
The caps for the xtal are both 22pF
I'm using the Serin program to get the data from serial
.
-
i can try using the internal osc...but will have to use MCLR on or i will lock my pic :S
IC-Prog has 2 choices...
INTOSC GP4
and
INTOSC CLKOUT
which one may i use ?
-
Quote:
I'm not using any Max232
AH CRAP, i really need new glasses... so just change your SEROUT2 baud constant to use inverted mode... and it will work
Code:
baud Serout2
---- -------
9600 16488
4800 16572
2400 16780
with 1-10K resistor in serie, this have to work.
I would suggest you to use DEBUG, it use less code space and may work on higher baudrate with slower crystal speed.
-
The SEROUT2 baud constant table did not worked as well...
but...
using DEBUG worked 5*****
I guess it's because the low speed xtal
Thanks once again Mister-e ;)
.
