Printable View
heya, I'm having a heck of a time getting a ds2438 onewire device to work on a 16f84a. I can't seem to get it to work worth anything. there are samples for other types of code in the onewire family, but I can't seem to modify the code example to work. I've got a 4.7k pullup resistor hooked up as per the example, but I have no code to let me know how to time it. also theres only one device on the bus..
Click the search button above, type in 1 wire device and it returns several example threads.
I've tried various code samples allready. I've used a few temp gathering programs with and without modification. all the programs I've tried so far have produced insane readings. the documentation for the 2438 is minimal, and virtually non-existant for picbasic. I believe that the architecture of the ds2438 is a little different than the other onewire devices.
Ahoy Captain,
Howz about lettin' us eyeball the code you are trying to adapt, lots of SMART people in here! Also tell us what PIC device you are using and what readings your getting. What readings you are expecting too. Oh and what clock speed you are using too. Please describe exactly what you are trying to get this device to measure, a schematic would be wonderful.
JS
http://www.maxim-ic.com/appnotes.cfm/appnote_number/27
http://www.maxim-ic.com/quick_view2.cfm/qv_pk/2919
Hello Captain Stern. This is a sample program for DS 2436 voltage and temp. monitor device. I hope it will help you
Best Regards
Vladimir
File...... DS2436 TEST1 modified.PBP
' Purpose... Reads information from a Dallas DS2436
' -----[ I/O Definitions ]------------------------------------------------------
'
OWpin CON 0
'DEFINE DEBUG_REG PORTB ' FOR DEBUG COMMAND
'DEFINE DEBUG_BIT 1 ' FOR DEBUG COMMAND
'DEFINE DEBUG_BAUD 2400 ' FOR DEBUG COMMAND
'DEFINE DEBUG_MODE 0 ' FOR DEBUG COMMAND
' -----[ Constants ]------------------------------------------------------------
'
' 1-Wire Support
'
ReadROM CON $33 ' read ID, serial num, CRC
MatchROM CON $55 ' look for specific device
SkipROM CON $CC ' skip rom (one device)
SearchROM CON $F0 ' search
OW_FERst CON %0001 ' Front-End Reset
OW_BERst CON %0010 ' Back-End Reset
OW_BitMode CON %0100
OW_HighSpd CON %1000
' DS2346 control
'
ConvertV CON $B4 ' convert the voltage
ConvertT CON $D2 ' convert the temperature
ReadRegister CON $B2 ' read page 4 and page 5 of DS2436
NoDevice CON %0 ' no device present
'DegSym CON 176
' -----[ Variables ]------------------------------------------------------------
'
voltage VAR Word
vLo VAR voltage.BYTE0
vHi VAR voltage.BYTE1
temp VAR Word
tLo VAR temp.BYTE0
tHi VAR temp.BYTE1
romData VAR Word(8)
devCheck VAR Word
' -----[ EEPROM Data ]----------------------------------------------------------
'
' -----[ Initialization ]-------------------------------------------------------
'
Initialize:
output 5
lcdout $fe, 1
portb.5 = 1
pause 1300 ' allow LCD screen to clear
portb.5 = 0
GOSUB Device_Check ' look for device
' debug bin devCheck ' test no 1-wire device
IF (devCheck <> NoDevice) THEN Main
No_Device_Found:
lcdout $fe, 1, "No 1-wire device"
lcdout $fe, $c0, "Insert device"
end
' -----[ Main Code ]------------------------------------------------------------
'
Main:
GOSUB Get_Volt ' voltage conversion
GOSUB Get_Temp ' temperature conversion
testValue1: ' voltage = $01E3 ' uncomment to test without DS2436
testValue2: ' temp = $1910 ' uncomment to test without DS2436
lcdout $fe, 1, "Voltage:" ,Dec voltage/100,".", DEC1 voltage/10,"v"
lcdout $fe, $c0, "Temperature:",DEC tHi, "C"
PAUSE 600 ' delay for a bit....
' debug dec voltage
GOTO Main
END
' -----[ Subroutines ]----------------------------------------------------------
'
'DS2436 Page 4 Memory is read using the Read_Registers [$B2] command
'addr purpose
' $60 Temp LSB (decimal degrees C)
' $61 Temp MSB (integer degrees C)
' $62 status (BIT0 shows T conversion status, Bit 3 shows V status)
' $63 status
' $77 Voltage LSB
' $78 Voltage MSB
Get_Volt:
OWOUT OWpin,OW_FERst,[SkipROM,ConvertV] ' send voltage conversion command
PAUSE 15 ' give it some time (could wait until bit3 at $62 equals 0)
OWOUT OWpin,OW_FERst,[SkipROM,ReadRegister, $77] ' lo byte voltage
OWIN OWpin,OW_BERst,[vLo]
OWOUT OWpin,OW_FERst,[SkipROM,ReadRegister, $78] ' hi byte voltage
OWIN OWpin,OW_BERst,[vHi]
RETURN
Get_Temp:
OWOUT OWpin,OW_FERst,[SkipROM,ConvertT] ' send voltage conversion command
PAUSE 15 ' give it some time (could wait until bit1 at $62 equals 0)
OWOUT OWpin,OW_FERst,[SkipROM,ReadRegister, $60] ' lo byte temp
OWIN OWpin,OW_BERst,[tLo]
OWOUT OWpin,OW_FERst,[SkipROM,ReadRegister, $61] ' hi byte temp
OWIN OWpin,OW_BERst,[tHi]
RETURN
' This subroutine checks to see if any 1-Wire devices are present on the
' bus. It does NOT search for ROM codes
Device_Check:
devCheck = 0
OWOUT OWpin,OW_FERst,[SearchROM] ' reset and start search
OWIN OWpin,OW_BitMode,[devCheck.BIT1,devCheck.BIT0]
RETURN