I need help with PIC 16F877A
I am new to PIC BASIC.
In attachment is my Flow Chart and Conections.
Thanks
Val
[email protected]
Printable View
I need help with PIC 16F877A
I am new to PIC BASIC.
In attachment is my Flow Chart and Conections.
Thanks
Val
[email protected]
Anything else????
No kidding...
I'll write the whole program, put it on a circuit board, test it, and deliver it to your house for $1,000 -- complete with a free pizza.
NOT!!!!
Why not show us an attempt...no matter how feeble...then maybe, just maybe, somebody around here will help you...myself included.
Until you've done some of the legwork, forget it...
JDG
I try to wrote code and for sure do a lot of mistakes.
Can you check code in Att. and help me.
Thanks
Let me post it here for you.
Code:
'****************************************************************
'* Name : TEST_Example.BAS *
'* Author : VAL *
'* Notice : Copyright (c) 2006 *
'* : All Rights Reserved *
'* Date : 11/27/2006 *
'* Version : 1.0 *
'* Notes : *
'* : *
'****************************************************************
program TEST_Example
'Project name:
' TEST_Example
' * Description:
' This project simulate real environment and test PLC response
' Configuration:
' MCU: PIC16F877A
' Oscillator: HS, 8 MHz
' Ext. Modules: ADC(MCP3204),Switches,LED Diodes
' * Notes:
' ADC on PORTC
' 2x16 LDC on PORTB (4-bit)
' LED Diodes on PORTA
' Switches on PORTD and PORTE
' 1000=1 second
PBP -p16F877A TEST_Example
DEFINE OSC 8
DEFINE ADCON1=7
DEFINE intcon=0
DEFINE LCD_DREG PORTB
DEFINE LCD_DBIT 0
DEFINE LCD_RSREG PORTB
DEFINE LCD_RSBIT 4
DEFINE LCD_EREG PORTB
DEFINE LCD_EBIT 5
DEFINE LCD_BITS 4
DEFINE LCD_LINES 2
DEFINE LCD_COMMANDUS 2000
DEFINE LCD_DATAUS 50
TRISB=0
LCD_Init(PORTB)
LCDOut $FE,$80+6,"TEST" 'I want to show TEST in the midle of first line on the display
LCDOut $FE,$0C+6,"START" 'I want to show START in the midle of second line
'Here I need code for ADC connected to PORTC
'CLK(SCK) to PORTC.3
'Dout(MISO) to PORTC.5
'Din(MOSI) to PORTC.4
'ADC is MCP3204 and I want To use CH0 and CH1
'CH0 will be var MODV and CH1 will be var CURRV
'Range is From 5 V to 0 V
TRISA=0
AA VAR PORTA.0 'PORTA is Output
BB VAR PORTA.1
CC VAR PORTA.2 'I connect diodes(AA,BB,CC,MM,NN,MDEF) to specific Pins
MM VAR PORTA.3
NN VAR PORTA.4
MDEF VAR PORTA.5
TRISD=1
ALARM VAR PORTD.0 'PORTD is Input
HEAT VAR PORTD.1
INRANGE VAR PORTD.2 'Togle switches are connected to specific Pins
DEFROST VAR PORTD.3
EVAL VAR PORTD.4
CF VAR PORTD.5 'Togle switch is RELAY that is ON or OFF
SSV VAR PORTD.6
COOL VAR PORTD.7 'ON=1 and OFF=0
TRISE=1
RET VAR PORTE.0 'PORTE same like PORTD
CM VAR PORTE.1
main:
ALARM1=ALARM 'Read status of PINA.0 (Can be GND or Vcc-0 or 1)
IF ALARM1=0 Then 'If ALARM1=0(Pin ALARM is GND) I want to show this on LCD
LCDOut $FE,$80+6,"TEST"
LCDOut $FE,$0C+6,"FAIL 1"
Else
LCDOut $FE,$80+6,"TEST"
LCDOut $FE,$0C+6,"PASS 1"
High CC 'Set CC to 1(Vcc) and rest to 0(GND)
Low BB
Low AA
Low MM
Low NN
Low MDEF
Pause 360000 'Keep that setings for 6 min
Count CF,360000,CF1 'During this 6 min read status of CF and SSV
Count SSV,360000,SSV1
IF CF1<2 OR SSV<2 Then 'During this 6 MIN check does CF AND SSV change
LCDOut $FE,$80+6,"TEST" 'they status min 2 times
LCDOut $FE,$0C+6,"FAIL 2"
Else
LCDOut $FE,$80+6,"TEST"
LCDOut $FE,$0C+6,"PASS 2"
ALARM1=ALARM
HEAT1=HEAT
INRANGE1=INRANGE 'Read status of inputs
DEFROST1=DEFROST
EVAL1=EVAL
COOL1=COOL 'I also need to read value of ANALOG INPUTS
RET1=RET 'CURRV must be betwen 2.5 V and 5 V
CM1=CM
IF EVAL1=0 OR CM1=0 OR INRANGE1=0 OR ALARM1=0 OR RET1=1 OR DEFROST1=1 OR HEAT1=1 OR COOL1=0 OR MODV1=0 OR CURRV1<2.5 Then
LCDOut $FE,$80+6,"TEST"
LCDOut $FE,$0C+6,"FAIL 3"
Else
LCDOut $FE,$80+6,"TEST"
LCDOut $FE,$0C+6,"PASS 3"
High CC 'Change status of output and keep that status 2 min
High BB
Low AA
Low MM
Low NN
Low MDEF
Pause 120000
Count CF,120000,CF1
IF CF1<2 Then
LCDOut $FE,$80+6,"TEST"
LCDOut $FE,$0C+6,"FAIL 4"
Else
LCDOut $FE,$80+6,"TEST"
LCDOut $FE,$0C+6,"PASS 4"
IF EVAL1=0 OR INRANGE1=0 OR CM1=0 OR MODV1>0 OR HEAT1=1 OR SSV1=1 OR DEFROST1=1 OR RET1=1 OR ALARM1=0 OR COOL1=1 OR CURRV1<2.5 Then
LCDOut $FE,$80+6,"TEST"
LCDOut $FE,$0C+6,"FAIL 5"
Else
LCDOut $FE,$80+6,"TEST"
LCDOut $FE,$0C+6,"PASS 5"
High AA
LOW BB
HIGH CC
LOW MM
LOW NN
LOW MDEF
PAUSE 180000
COUNT IR,180000,IR1
IF IR1=0 THEN
LCDOut $FE,$80+6,"TEST"
LCDOut $FE,$0C+6,"FAIL 6"
ELSE
LCDOut $FE,$80+6,"TEST"
LCDOut $FE,$0C+6,"PASS 6"
IF EVAL1=0 OR HEAT1=0 OR CF1=1 OR CM=1 OR SSV1=1 OR DEFROST1=1 OR ALARM1=0 OR RET1=1 or COOL=1 OR HEAT1=0 OR MODV1>0 OR 0.9<CURRV1<1.8 THEN
LCDOut $FE,$80+6,"TEST"
LCDOut $FE,$0C+6,"FAIL 7"
ELSE
LCDOut $FE,$80+6,"TEST"
LCDOut $FE,$0C+6,"PASS 7"
LOW AA
HIGH BB
HIGH CC
LOW MM
LOW NN
LOW MDEF
PAUSE 30000
LOW AA
HIGH BB
HIGH CC
HIGH MM
LOW NN
LOW MDEF
PAUSE 15000
LOW AA
HIGH BB
HIGH CC
LOW MM
HIGH NN
LOW MDEF
PAUSE 1000
LOW AA
HIGH BB
HIGH CC
LOW MM
LOW NN
LOW MDEF
PAUSE 120000
IF EVAL1=0 OR CM1=0 OR SSV1=0 OR HEAT1=1 OR DEFROST1=1 OR ALARM1=0 OR RET1=1 OR COOL=0 OR MODV1<2.5 OR CURRV1<2.5 THEN
LCDOut $FE,$80+6,"TEST"
LCDOut $FE,$0C+6,"FAIL 8"
ELSE
LCDOut $FE,$80+6,"TEST"
LCDOut $FE,$0C+6,"PASS 8"
LOW AA
HIGH BB
HIGH CC
HIGH MM
HIGH NN
LOW MDEF
PAUSE 15000
LOW AA
HIGH BB
HIGH CC
LOW MM
HIGH NN
LOW MDEF
PAUSE 1000
LOW AA
HIGH BB
HIGH CC
LOW MM
LOW NN
LOW MDEF
PAUSE 30000
LOW AA
HIGH BB
HIGH CC
LOW MM
LOW NN
HIGH MDEF
PAUSE 1000
LOW AA
HIGH BB
HIGH CC
LOW MM
LOW NN
LOW MDEF
PAUSE 60000
IF DEFROST1=0 OR HEAT1=0 OR ALARM1=0 OR MODV1>0 THEN
LCDOut $FE,$80+6,"TEST"
LCDOut $FE,$0C+6,"FAIL 9"
ELSE
LCDOut $FE,1,"I AM GOOD"
LCDOut $FE,$0C,"TO GO"
Endif
ENDIF
ENDIF
ENDIF
ENDIF
ENDIF
ENDIF
ENDIF
ENDIF
END
I just posted your code.
I did not change anything in it.
--------------------