Variable changing mid-code in 16F883?

I've been trying to figure out what's going on with this code, but for the life of me I can not. I've posted the whole code, but I believe the issue is in the loop titled "pulse_test". The variable "address" should increment by 16 every second time it goes through the loop, immediately after an EEPROM write. However it appears to be changing randomly during the program. I've added some debug statements and slowed down timer1 which is polled to space out measurements. After pressing STRT_BUT, some variables are set and it goes into "pulse_test". The output of the debug statements are shown below. As shown, address initially increments to 16 correctly but then is 13344 at the start of the next loop. I was sure there was a typo, but now wondering if it's something in the hardware I have set incorrectly? The loop is supposed to measure A, measure B every 8th loop, measure C, write to EEPROM every other loop, repeat. Any suggestions or thoughts are much appreciated!

"THERMAL START
A0-0-0
B0-0-0
C0-1-0
A0-2-0
C0-3-0
D0-3-16
A0-4-13344
C0-5-13344
A0-6-13344
C0-7-13344
D0-7-13360
A0-8-13360
C0-9-13360
A0-10-13360
C0-11-13360
D0-11-13376
A0-12-13376
C0-13-13376
A0-14-13376
C0-15-13376
D0-15-13392
A0-1-13392
C0-2-13392
A0-3-13392
C0-4-257
A0-5-257
C0-6-257
A0-7-257
C0-8-257"

Code:

---

#CONFIG
__config _CONFIG1, _HS_OSC & _WDT_OFF & _MCLRE_OFF & _LVP_OFF & _CP_OFF
__CONFIG _CONFIG2, _WRT_OFF & _BOR21V
#ENDCONFIG

'INTERRUPT VARS
'wsave  var byte $70 system 'needed for interrupt
'wsave  var byte    $70 SYSTEM
'wsave1  VAR BYTE    $A0    SYSTEM      ' location for W if in bank1
'wsave2  VAR BYTE    $120    SYSTEM      ' location for W if in bank2
ibit    var bit
icount  var byte
'GENERAL VARS
tempbit var bit
wrbit  var bit
tempvar var word
tempvar2 var word
tempbyt var byte
n      var byte
current var word
voltage var word
EDATA  var word[4]
hbyte  var byte
lbyte  var byte
TIME1  var word
TIME2  var word
'HX711 specific
HX711A  var Word
'MAX6675 specific
MXTemp  var word
'ADS1115 specific
adrs_w  var byte
adrs_r  var byte
config1 var byte
config2 var byte
CNFGREG VAR BYTE
CNVRREG var byte
'EEPROM specific
wconfig        var byte
rconfig        var byte
address var word

ABRT_BUT var PORTA.1
STRT_BUT VAR PORTA.0
DIAG_BUT VAR PORTE.3
LED      var portA.2
Hdta    var PORTA.3  'HX711 pins
Hclk    var PORTA.4  'HX711 pins
PIN_OUT  var PORTC.3  'serial out pin
PIN_IN  var PORTC.2  'serial in pin
ADC_CLK  var PORTC.1  'ADC clock pin
ADC_DAT  var PORTC.0  'ADC data pin
ADC_RDY  var PORTA.5  'ADC alert/ready pin
EE_CLK  var PORTC.5  'I2C EEPROM clock pin
EE_DAT  var PORTC.4  'I2C EEPROM data pin
MXDATA  var PORTB.5  'MAX6675 DATA pin (was HX711 pin)
MXCLK    var PORTB.7  'MAX6675 CLOCK pin (was HX711 pin)
MXCS    var PORTB.6  'MAX6675 Chip Select
MOT_PWM  var PORTB.4  'MOTOR PWM OUTPUT

'INCLUDE "DT_INTS-14.bas" ' Base Interrupt System
'INCLUDE "ReEnterPBP.bas" ' Include if using PBP interrupts

T1CON = %00110000 ' Prescaler = 1:1,  Timer off

ANSEL=%00000000      'all analogue ports to digital
ANSELH=%00000000    'all analogue ports to digital
ADCON0.0=0          'disable ADC
CM1CON0=%00000000    'disable COMPARATOR 1
CM2CON0=%00000000    'disable COMPARATOR 2
SSPCON=%00000000    'disable SERIAL PORT
RCSTA=%00000000      'disable SERIAL PORT
PCON=%00000000      'disable BOR and ULPW

TRISA=%00101011      '(0=output, 1=input)
TRISB=%00100001      '(0=output, 1=input)
TRISC=%00000000      '(0=output, 1=input)
TRISE=%00001000      '(0=output, 1=input)

OPTION_REG=%11000101

define OSC 20

low MOT_PWM
low Hclk
HIGH MXCS
HIGH EE_CLK

for n = 0 to 9
high LED
pause 100
low LED
pause 100
next n

'setup EEPROM
wconfig=%10100000
rconfig=%10100001

'setup ADC configuration
adrs_w=$48
adrs_w=adrs_w<<1 ' Add read/write bit at end (0=write)
adrs_r=adrs_w+1  ' Add read/write bit at end (1=read)
CNFGREG=$01      ' Address of the configuration register
CNVRREG=$00      ' Address of the conversion register

waitforstart:
if STRT_BUT=0 then waitforstart

config1=%11010001  ' A+ = A1, A- = GND
config2=%11100011
I2CWRITE ADC_DAT,ADC_CLK,adrs_w,CNFGREG,[config1,config2] 'set config register
ibit=0
address=0
icount=0
pause 2
TMR1H=0
TMR1L=0

tempbyt=0

serout2 PIN_OUT,32,["THERMAL START",13,10] '19200bps
high LED

@ bsf    T1CON, TMR1ON  ' Start timer
'@ INT_ENABLE TMR1_INT ; enable TMR1 interrupts
pulse_test:
TIME2.highbyte=tempbyt
I2CWRITE ADC_DAT,ADC_CLK,adrs_w,[CNVRREG] 'point to conversion register
I2CREAD ADC_DAT,ADC_CLK,adrs_r,[hbyte,lbyte] 'read voltage from ACS712 (current sensor) via ADC
current.highbyte=hbyte
current.lowbyte=lbyte
EDATA[icount]=current 
'switch ADC to channel A2 (batt voltage)
config1=%11100001 'A+ = A2, A- = GND
I2CWRITE ADC_DAT,ADC_CLK,adrs_w,CNFGREG,[config1,config2] 'write config register channel
serout2 PIN_OUT,32,["A",dec ibit,"-",dec icount,"-",dec address,13,10] 
if icount=0 then
LOW MXCS
shiftin MXDATA,MXCLK,0,[MXTemp\16]  'read the data to MXTemp
HIGH MXCS
serout2 PIN_OUT,32,["B",dec ibit,"-",dec icount,"-",dec address,13,10] 
endif

hold1:
tempbyt=TMR1H
if tempbyt<>128 then hold1
TIME2.LOWbyte=tempbyt
icount=icount+1
I2CWRITE ADC_DAT,ADC_CLK,adrs_w,[CNVRREG] 'point to conversion register
I2CREAD ADC_DAT,ADC_CLK,adrs_r,[hbyte,lbyte] 'read batt voltage through 1/2 voltage divider via ADC
voltage.highbyte=hbyte
voltage.lowbyte=lbyte
EDATA[icount]=voltage
'switch ADC to channel A1 (current)
config1=%11010001  ' A+ = A1, A- = GND
I2CWRITE ADC_DAT,ADC_CLK,adrs_w,CNFGREG,[config1,config2] 'write config register channel
tempbyt=icount & %00000011
serout2 PIN_OUT,32,["C",dec ibit,"-",dec icount,"-",dec address,13,10]
if tempbyt=3 THEN
I2CWRITE EE_DAT,EE_CLK,wconfig,address,[EDATA[0],EDATA[1],MXTemp,TIME1,EDATA[2],EDATA[3],MXTemp,TIME2]
address=address+16
serout2 PIN_OUT,32,["D",dec ibit,"-",dec icount,"-",dec address,13,10]
toggle LED
endIF
icount.bit4=0 'rollover from 15 to 0
if address=1600 then goto readout
TIME1=TIME2
hold2:
tempbyt=TMR1H
if tempbyt<>128 then hold2
icount=icount+1
goto pulse_test

readout:
'@ INT_DISABLE TMR1_INT ; enable TMR1 interrupts
low MOT_PWM
serout2 PIN_OUT,32,["READOUT",13,10]
low LED
for tempvar=0 to 105
address=tempvar<<3
I2CREAD EE_DAT,EE_CLK,rconfig,address,[current,voltage,MXTemp,TIME1]
serout2 PIN_OUT,32,[dec tempvar," ",dec current," ",dec voltage," ",MXTemp," ",TIME1.highbyte," ",TIME1.lowbyte,13,10]             
next tempvar
goto waitforstart

END

---

Quote:

---

for tempvar=0 to 105
address=tempvar<<3

---

that looked wrong at first if address started a 1600 but it doesn't.
perhaps address gets corrupted every time readout is run,
spaghetti code like that is hard to unravel

I'm not saying this is related to your problem but here:

Code:

---

hold1:
  tempbyt=TMR1H
  if tempbyt<>128 then hold1

---

This will "hold" until TMR1H is 128 and then countinue.
But for how long is TMR1H 128? Are you sure it's not (still) 128 the next time you check?

I would rewrite this.
* For pacing the loop, poll the TMR1 interrupt flag.
* Create a short subroutine for each "task". MeasureA, MeasureB, MeasureC, WriteEEPROM and so on.
* Have a LoopCount variable that counts from 0 to whatever.
* Use a Select Case block to execute whatever tasks are needed at each increment of the loop.

Crude example:

Code:

---

TMR1IF VAR PIR1.0
LoopCount VAR BYTE

TMR1IF = 0
T1CON = %00110001 ' Prescaler = 1:8,  Timer ON

Main:
  IF TMR1IF=0 THEN Main    ' Wait for TMR1 roll over

  TMR1IF=0                  ' Reset interrupt flag.

  Select Case LoopCount
    Case 0
      GOSUB MeasureA
      GOSUB MeasureB

    Case 1
    GOSUB MeasureA
    GOSUB MeasureC

    Case 2
      GOSUB MeasureA
      GOSUB MeasureB
      GOSUB MeasureC

    Case 3
      GOSUB MeasureB
      GOSUB MeasureC
      GOSUB WriteEEPROM
  END SELECT

  LoopCount = LoopCount + 1
  IF LoopCount = 4 THEN LoopCount = 0

Goto Main


MeasureA:
  ' Do stuff
RETURN

MeasureB:
  ' Do Stuff
RETURN

MeasureC:
  ' Do Stuff
RETURN

WriteEEPROM:
  ' Do Stuff
RETURN

---

i had a slightly different take but am amazed at the similarity

Code:

---


#CONFIG
    __config _CONFIG1, _HS_OSC & _WDT_OFF & _MCLRE_OFF & _LVP_OFF & _CP_OFF
    __CONFIG _CONFIG2, _WRT_OFF & _BOR21V
#ENDCONFIG


DEFINE INTHAND  ticker 






ANSEL=0      'all analogue ports to digital
ANSELH=0    'all analogue ports to digital




TRISA=%00101011      '(0=output, 1=input)
TRISB=%00100001      '(0=output, 1=input)
TRISC=%00000000      '(0=output, 1=input)
TRISE=%00001000      '(0=output, 1=input)


OPTION_REG=%11000101
PIN_OUT      var PORTC.3  'serial out pin
LED          var portA.2
wsave        var byte    $70 SYSTEM
ssave        var byte    SYSTEM
psave        var byte    SYSTEM
taskflag      var byte
taskswitch    var byte
ro_counter    var byte
ibit          var byte
address      var word
icount        var word


define OSC 20


intcon =$c0
pir1.0=0
pie1.0=1


serout2 PIN_OUT,32,["THERMAL START",13,10] '19200bps
T1CON=$31




main:
    if taskflag then
          taskflag = 0
          taskswitch = taskswitch + 1
          if taskswitch == 4 then  taskswitch = 0
          select case taskswitch
              CASE 0
                gosub task0
                serout2 PIN_OUT,32,["A",dec ibit,"-",dec icount,"-",dec address,13,10]
                serout2 PIN_OUT,32,["B",dec ibit,"-",dec icount,"-",dec address,13,10] 
              case  1
                gosub task1
                icount=icount+1
                serout2 PIN_OUT,32,["C",dec ibit,"-",dec icount,"-",dec address,13,10]
                address=address+16
                serout2 PIN_OUT,32,["D",dec ibit,"-",dec icount,"-",dec address,13,10]
              case  2
                gosub task2
                ro_counter =ro_counter +1
                if ro_counter == 16 then
                    serout2 PIN_OUT,32,["READOUT",13,10]
                    ro_counter =0
                endif
              case  3
                gosub task3
               
          end select   
    endif
goto main


task0:
'do voltage stuff
return


task1:
'do current stuff
return


task2:
'do other stuff
return


task3:
    LED = ! led
return




END


asm   
ticker      ;tmr1 isr
    banksel  _taskflag
    bsf _taskflag,0
    banksel PIR1
    bcf PIR1,0
    movf psave,W ; restore PCLATH
    movwf PCLATH
    swapf ssave,W ; restore STATUS
    movwf STATUS
    swapf wsave,F ; restore W (swap avoids changing STATUS)
    swapf wsave,W
    RETFIE   
endasm

---