Pls tell me what is the use of comparator voltage reference module?
Printable View
Pls tell me what is the use of comparator voltage reference module?
To provide the comparator(s) with an internally generated reference voltage so you don't have to "waste" a second I/O pin for that.
It also allows one to change the comparator voltage in software.
Actually in my temperature controller circuit ADC value fluctuates with wide range when a heavy load through a relay is connected.I am using 16f876a micro and Pin A0 as ADC input.
Sounds like you want to buffer that relay.
George
If the load is a motor, current spikes on start-up. Might want to average sampling, or delay between samples.
Robert
Load is 4 kw heater.Somebody in here in Lucknow ( India) told me to use comparator voltage reference module.I don't know what to do .Confused.
Pause for a few seconds when the relay is activated, then start taking samples.
Robert
Here is my code_----
'DIGITAL TEMP CNTROLLER USING 16F876A'
DG1 VAR BYTE
DG2 VAR BYTE
DG3 VAR BYTE
DIGIT VAR BYTE
DG VAR BYTE
COUNTT VAR BYTE
NUMB VAR WORD
N VAR WORD
adval var word
temp var word
TEMPP VAR WORD
ADCON1=%10000000
adcon0=%00000101
TRISA=1
TRISB=%00111000
TRISC=0
gosub mread
n=numb
GOSUB DIGITCALC
'-------------------------------------------------------------------------
MAIN1:
GOSUB DISPLAY
IF PORTB.3=1 THEN MREAD
IF PORTB.3=0 THEN MAIN
GOTO MAIN1
'-------------------------------------------------------------------------
MAIN:
ADCON0.2=1
GO:
IF ADCON0.2=1 THEN GO
adval.HIGHBYTE = ADRESH
adval.lowbyte = ADRESL
'temp=(adval*500)/1024
temp=adval
N=temp
gosub display
gosub digitcalc
If adval>NUMB then PORTB.7=0
pause 1000
IF ADVAL< NUMB-5 THEN PORTB.7=1
pause 1000
GOTO MAIN1
'_____________________________________
UP:
IF NUMB=400 THEN MAIN
NUMB=NUMB+1
N=NUMB
GOSUB DIGITCALC
IF PORTB.4=1 THEN MEMORY
GOTO MAIN1
memory:
WRITE 0,numb.HighByte
WRITE 1,numb.LowByte
GOTO MAIN1
'_____________________________________
DOWN:
IF NUMB=0 THEN MAIN 'MIN LIMIT
NUMB=NUMB-1
N=NUMB
GOSUB DIGITCALC
IF PORTB.5=1 THEN MEMORY
GOTO MAIN1
'_____________________________________
MREAD:
READ 0,numb.HighByte
READ 1,numb.LowByte
n=numb
gosub digitcalc
IF PORTB.4=1 THEN UP
IF PORTB.5=1 THEN DOWN
goto main1
__________________________________________________ _
DISPLAY:
FOR COUNTT=0 TO 99
PORTC=DG1
PORTB.2=1
PAUSEUS 300
PORTB.2=0
PORTC=DG2
PORTB.1=1
PAUSEUS 300
PORTB.1=0
PORTC=DG3
PORTB.0=1
PAUSEUS 300
PORTB.0=0
NEXT COUNTT
RETURN
'_________________________________________________ _______________
'_________________________________________________ _________________________
DIGITCALC:
DIGIT=0
LP1:
IF N<100 THEN DS1
N=N-100
DIGIT=DIGIT+1
GOTO LP1
DS1:
GOSUB FND
DG1=DG
DIGIT=0
LP2:
IF N<10 THEN DS2
N=N-10
DIGIT=DIGIT+1
GOTO LP2
DS2:
GOSUB FND
DG2=DG
DIGIT=N
GOSUB FND
DG3=DG
RETURN
'_________________________________________________ _________________________
'_________________________________________________ _________________________
FND:
FND0:
IF DIGIT>0 THEN FND1
DG=$7E '%0111 1110
GOTO FNDEND
FND1:
IF DIGIT>1 THEN FND2
DG=$48 '%0100 1000
GOTO FNDEND
FND2:
IF DIGIT>2 THEN FND3
DG=$3D '%0011 1101
GOTO FNDEND
FND3:
IF DIGIT>3 THEN FND4
DG=$6D '%0110 1101
GOTO FNDEND
FND4:
IF DIGIT>4 THEN FND5
DG=$4B '%0100 0011
GOTO FNDEND
FND5:
IF DIGIT>5 THEN FND6
DG=$67 '%0110 0111
GOTO FNDEND
FND6:
IF DIGIT>6 THEN FND7
DG=$77 '%0111 0111
GOTO FNDEND
FND7:
IF DIGIT>7 THEN FND8
DG=$4C '%0100 1100
GOTO FNDEND
FND8:
IF DIGIT>8 THEN FND9
DG=$7F '%0111 1111
GOTO FNDEND
FND9:
DG=$6F '%0110 1111
FNDEND:
RETURN
'_________________________________________________ _________________________
Comments would be helpful.
My problem is solved by using a 220 uf capacitor in my thermocouple amplifier. Now another problem arose .I think my circuit hangs.After running fine for a hour display on seven segment goes off.When I re- start circuit it works again.What can I do to rectify it.
Hard to answer without a schematic.
How is your power supply, enough current? Do other devices turn on during this time and take up too much current?
EDIT: Blink a LED in this part just to be sure nothing is going wrong.
Code:MAIN:
ADCON0.2=1
GO:
IF ADCON0.2=1 THEN GO
I will share my schematic tomorrow? Thanks Demon ( ji)