How to receive and analyze text via SERIN ?
Hello.
I want to receive text via SERIN and do actions based on it. Like in exampole below
Code:
CIKLI:
Serin SHESVLA,N2400,MONACEMI 'READ INTO VARIABLE
if monacemi="X" then
CCP1CON = %00000000
goto cikli
this works fine, while "X" is single character, when I'd like to make it say "hamex", the code does not works.
Re: How to receive and analyze text via SERIN ?
Quote:
Originally Posted by
CuriousOne
this works fine, while "X" is single character, when I'd like to make it say "hamex", the code does not works.
Just from WAG, HAMEX is a string, so I "think" you would need to read it into an array and test the array for the value of each letter.
Re: How to receive and analyze text via SERIN ?
Couple of years ago I had a similar problem/question.
See this post. It might help you.
Re: How to receive and analyze text via SERIN ?
Ok, this works, setup for a 16F690 demo board
Code:
@ __config _INTRC_OSC_NOCLKOUT & _WDT_ON & _MCLRE_OFF & _CP_OFF
DEFINE OSC 4
DEFINE DEBUG_MODE 0 ' Debug sending True serial data
DEFINE DEBUG_REG_PORTA ' Debug Port = PortA as required by PICKIT2 serial Monitor
DEFINE DEBUG_BIT 0 ' Debug.bit = PortA.0
DEFINE DEBUG_BAUD 9600 ' Default baud rate = 9600
DEFINE DEBUGIN_REG PORTA' Debug Port = PortA as required by PICKIT2 serial Monitor
DEFINE DEBUGIN_BIT 1 ' Debugin bit PortA.1
DEFINE DEBUGIN_BAUD 9600' Default baud rate = 9600
DEFINE DEBUGIN_MODE 0 ' Debugin receiving data true = 0 inverted = 1
ANSEL=0
ANSELH=0
ADCON0 = 0
ADCON1 = 0
;CCP1CON = %10001100 ;Dual PWM 10xx11xx P1A/RC5 P1B/RC4 RC3/AN7 RC2/AN6
TRISA = %00000010
TRISB = %00000000
portC = 0
TrisC = %00000000
tank var byte[5]
tank = 0
main:
debugin[str tank\5]
PAUSE 30
if (tank[0] = "H") AND (tank[1] = "A") AND (tank[2] = "M") AND (tank[3] = "E") AND (tank[4] = "X")THEN
gosub flash
debug " tank"," ",str tank\5
else
debug " FAIL"
endif
goto main
flash:
portc.0 = 1
pause 500
portc.0 = 0
pause 500
return
end
If HAMEX is sent it flashes the led on portc.0, if anything else, is sent it responds with FAIL
Re: How to receive and analyze text via SERIN ?
Wow, thank you very much!
Re: How to receive and analyze text via SERIN ?
Here is a very good example of how to compare strings. The comparisons are done in Check_List.
Quote:
Originally Posted by
dan-tron
EUREKA!
Thanks guys! You have been a huge help. I have finally figured it out.
My problem was more like 3 problems...
1. I have never done EEPROM stuff before so I was lost to begin with.
2. As Bruce pointed out, the mathematical order of operations in one line was not correct. I guess the BS2 thinks a little differently from PBP in that respect.
3. My PicBasic Pro compiler was Version 2.30 form 2000. It seems that v2.30 supports the PIC 16F628 but the PIC 16F628A was implemented in a later version. I have upgraded my PBP to version 2.47 and now the EEPROM features work correctly on the 16F628A. When I successfully tested a 16F84A using the same code, that lead me to question the compiler.
So for future generations and the benefit of other people like me, here's my WORKING code that is tested successfully on a PIC 16F628A with a 20MHz resonator compiled using PBP v2.47. It reads data from the Parallax RFID Reader Module, compares it against known values stored in EEPROM and allows or denies access accordingly. Enjoy.
Code:
CMCON = 7
DEFINE OSC 20 'Set oscillator in MHz
' -----[ Variables ]-------------------------------------------------------
buf VAR Byte(10) ' RFID bytes buffer
tagNum VAR Byte ' from EEPROM table
idx VAR Byte ' tag byte index
char VAR Byte ' character from table
' -----[ EEPROM Data ]-----------------------------------------------------
Tag1 DATA "100050A4B7"
Tag2 DATA "1000508E0A"
Tag3 DATA "10005091DC"
Tag4 DATA "100050203A"
Tag5 DATA "100050DA36"
' -----[ Initialization ]--------------------------------------------------
HIGH portb.3 ' turn off RFID reader
LOW portb.6 ' lock the door!
Low portb.4 'Turn off LED
' -----[ Program Code ]----------------------------------------------------
Main:
LOW portb.3 ' activate the reader
SERIN2 portb.2, 396, [WAIT($0A), STR buf\10] ' wait for hdr + ID
HIGH portb.3 ' deactivate reader
Check_List:
FOR tagNum = 1 to 5 ' scan through known tags
FOR idx = 0 TO 9 ' scan bytes in tag
READ (((tagNum-1) * 10) + idx), char ' get tag data from table
IF (char <> buf(idx)) THEN Bad_Char ' compare tag to table
NEXT
GOTO Tag_Found ' all bytes match!
Bad_Char: ' try next tag
NEXT
Bad_Tag:
tagNum = 0
FREQOUT portb.5, 1000 */ $100, 115 */ $100 ' groan
PAUSE 1000
GOTO Main
Tag_Found:
HIGH portb.6 ' remove latch
High portb.4 ' Light LED
FREQOUT portb.5, 2000 */ $100, 880 */$100 ' beep
LOW portb.6 ' restore latch
Low portb.4 ' LED OFF
GOTO Main
