Re: PBP and DT_INTs problems
Quote:
Originally Posted by
comwarrior
2) DT_INTs does not jump to interrupt subroutine on 16F1824 when ether external int or IOC pin is toggled.
And neither would any ON INTERRUPTs, ASM interrupts or simple IF PORTA.2 = 1 tests, since you haven't enabled Digital inputs on your Analog pins.
Re: PBP and DT_INTs problems
old config with comments for the same size PIC as 16F1824 ( well close ) this is for 16F1825 , as a ref hope it may be useful
cheers
Code:
' config for 16F1825
#CONFIG
;----- CONFIG1 Options --------------------------------------------------
__config _CONFIG1, _FOSC_INTOSC & _WDTE_OFF & _PWRTE_ON & _MCLRE_ON & _CP_OFF & _CPD_OFF & _BOREN_ON & _CLKOUTEN_OFF & _IESO_OFF & _FCMEN_ON
;----- CONFIG2 Options --------------------------------------------------
__config _CONFIG2, _WRT_OFF & _PLLEN_OFF & _STVREN_ON & _BORV_HI & _LVP_OFF
#ENDCONFIG
' ---------- Set up DT_INTS-14 Routine for Instant Interupt handling -----------
INCLUDE "DT_INTS-14.bas"
INCLUDE "ReEnterPBP.bas"
ASM
INT_LIST macro ; IntSource , Label , Type, ResetFlag?
INT_Handler TMR0_INT,_Timer0_Count, PBP, yes ; call Timer0_Count subroutine
INT_Handler IOC_INT,_GetIRcode , PBP, yes ; call GetIRcode subroutine on Interupt
endm
INT_CREATE ; Creates the Interrupt Processor
ENDASM
#HEADER
ERRORLEVEL -306 ; Suppress page boundry warning for DT_INTS-14 macro during a compile
#ENDHEADER
'----------- 16F1825 - PIC chip settings --------------------
OSCCON = $70 ' Select 8Mhz , internal clock
' Bit 7 0 = 4xPLL disabled 1= 4xPLL enables ( overrided by conf word 2 setting - PLLEN)
' bits6-3 - 1111 = 16Mhz , 1110 = 8MHz or 32Mhz ( depends on 4xPLL - conf word 2) 1101 = 4 MHz, 1100 = 2MHz 1011 = 1MHz
' bitS 0-1 - 00= Clock set by Conf word ,01 = Timer1 OSC , 1x = internal Osc Block
APFCON0 = %00000000 'All Default - No change when using SPI use SDO1 = RC2 , bit6=0
APFCON1 = %00000000 'All Default APFCON1 = %00000000
CM1CON0 = $00 ' Disable / Clear comparator 1
CM1CON1 = $00 ' Used with CM1CON0
CM2CON0 = $00 ' Disable / Clear comparator 2
CM2CON1 = $00 ' Used with CM2CON0
CMOUT = $00 ' Disable Comparitors output register - used only if comparitor on
ANSELA = %00000000 ' Set Port A - Digital I/O , 0 = Digital 1 = Analog
ANSELC = %00000000 ' Set Port C - Digital I/O , 0 = Digital 1 = Analog
INLVLA = %00000000 ' Set Port A to TTL Levels 0 = TTL , 1 = SCHMITT TRIGGER - Used port reads and Interupt on Change
INLVLC = %00000000 ' Set Port C to TTL Levels 0 = TTL , 1 = SCHMITT TRIGGER - Used port reads and Interupt on Change
SRCON0 = %00000000 ' Disable Latched Outputs
SRCON1 = %00000000 ' Used with SRCON0 register
ADCON0 = $00 ' Disable A/D
ADCON1 = $00 ' Disable A/D - used with ADCON0 settings
WPUA = %00001100 ' Port A - Turn off week Pullups 1=ON , for each port ( globle enable set in option_reg.7)set wpu on PortA.3 as input only - ref spec
WPUC = %00000000 ' Port C - Turn off week Pullups 1=ON For each port
DACCON0 = $00 ' Disable D/A
DACCON1 = $00 ' Disable D/A - used with DACCON0
FVRCON = $00 ' Disable Fixed Voltage Ref
IOCAN.4 = 1 ' Enable interupt on change on portA.4 for negative going edge ( for getIR routine )
IOCAF.4 = 0 ' Clear Interupt on Change flag on portA.4
OPTION_REG.7 = 1 ' Weak Pullups disabled 1 = globel disable 0 = globel enable ( set by each port - WPUA & WPUC settings)
OPTION_REG.6 = 0 ' Interupt on Falling Edge of INT pin 0= falling edge 1= rising edge
OPTION_REG.5 = 0 ' TMR0 clock source - 1=T0clk pin 0=internal clock
OPTION_REG.4 = 0 ' TMR0 0=L/H of TOCKI pin 1=H/L of TOCKI pin
OPTION_REG.3 = 0 ' Use Prescaller for TMR0 0= Yes , 1 = No
OPTION_REG.2 = 1 ' Timer0 prescaler Rate Select bits 2-0(set to 1:256)
OPTION_REG.1 = 1 ' 000 = 1:2 , 001= 1:4 , 010 = 1:8 , 011 = 1:16
OPTION_REG.0 = 1 ' 100 = 1:32 , 101 = 1:64, 110 = 1:128 , 111 = 1:256
T1CON = %01110100 ' Timer 1 ,bit7-6 = TMR1 CLK source 00 = Instuction Clk(Fosc/4),01 =sys clk,10=ext clk,11=cap sense osc
' bit5-4 = TMR1 prescale 11= 1:8 ,bit3=0 LP off,bit2=1 no sync ext CLK ,bit1= 0 n/a,Bit0=0 Timer 1 on/off
T1GCON = %00000000 ' Timer 1 Gate Control bit7 0= counts regardless of gate 1 = gates in use , bit6 gate active when 1= High ,0=low
' bit5 0= toggle mode diabled 1= enabled bit4 single pulse mode 1- en 0= dis, bit 2 -status bit,1-0 - gate source sel
T2CON = %01110011 ' Timer 2 off + 1:15 postscale ,1:64 prescale ( bit 7 = x, bit6-3 1110 = 1:15 postscale, bit2=0 timer off ,bit1-0 = prescale 10 = 16 , 11= prescale 64
T4CON = %00000000 ' POSTSCALER 1/1,STOP,PRESCALER 1/1
T6CON = %00000000 ' POSTSCALER 1/1,STOP,PRESCALER 1/1
TMR0 = 0 ' Clear TMR0 MODULE REGISTER
TMR1H = 0 'CLEAR TMR1H MODULE REGISTER
TMR1L = 0 'CLEAR TMR1L MODULE REGISTER
TMR2 = 0 'CLEAR TMR2 MODULE REGISTER
TMR4 = 0 'CLEAR TMR4 MODULE REGISTER
TMR6 = 0 'CLEAR TMR6 MODULE REGISTER
'PR2 = 255 ' Timer 2 Preload value
'PR4 = 255 ' Timer 4 Preload value
'PR6 = 255 ' Timer 6 Preload value