Using CCP1 and CCP2 in capture mode with Timer1.

Greetings to everybody

I have a question regarding the use of the CCP modules on a 16F876.

Currently I am using CCP1 with Timer1 to measure the length of a pulse (rising edge) in the main part of my program and all is fine. What I would now like to be able to do, as a precursor to the main part of the program running, is to measure two different pulses one via CCP1 followed by the second via CCP2. This second pulse is of a different frequency and from another source.

I set up these variables first.

Code:

capture VAR PIR1.2 ' CCP1 capture flag capture2 VAR PIR2.0 ' CCP2 capture flag overflow VAR PIR1.0 ' Timer1 overflow flag period var Word ' Pulse 1 Rising edge trigger period2 var word ' Pulse 2 Rising edge trigger

followed by these constants.

Code:

Constants CCP1CON = %00000101 'Enable the CCP1 capture, every rising edge. CCP2CON = %00000101 'Enable CCP2 for every capture.

I then call a Gosub routine that loops a number of times (not shown here) and outputs each result to the serial port for use within a pc program.

Code:

gratio: T1CON = %00010000 ' TMR1 prescale=1:4 Timer OFF _ %00010000 1:2 TMR1H = 0 ' Zero the Timer High TMR1L = 0 ' Zero the Timer Low capture = 0 capture2 = 0 StartLoop1: IF (capture = 0) Then StartLoop1 ' Wait here for the first capture T1CON.0 = 1 ' Start the Timer capture = 0 ' Reset the capture flag CaptureLoop1: IF (capture = 0) Then CaptureLoop1 ' Wait here until captured period.lowbyte = CCPR1L ' Store the captured value in period.highbyte = CCPR1H ' period variable GOSUB ClearTimer StartLoop2: IF (capture2 = 0) Then StartLoop2 ' Wait here for the first capture T1CON.0 = 1 ' Start the Timer capture2 = 0 ' Reset the capture flag CaptureLoop2: IF (capture2 = 0) Then CaptureLoop2 ' Wait here until captured period2.lowbyte = CCPR2L ' Store the captured value in period2.highbyte = CCPR2H ' period variable GOSUB ClearTimer Hserout [#period," ",#period2,13,10] 'Send result to serial port RETURN ClearTimer: ClearTimer1: IF (capture = 0) Then cleartimer1 ' Wait for beginning of next period TMR1L = 0 ' Clear Timer1 low register TMR1H = 0 ' Clear Timer1 high register capture = 0 ' Clear capture flag capture2 = 0 ' Clear capture flag overflow = 0 ' Clear overflow flag Return

What I have found is that the capture result is initially correct but the capture2 result is approximately capture+capture2. All further results after the initial loop are incorrect, it is as if the timer is not resetting correctly.

What am I doing wrong?.

I suspect that I have missed something simple, unfortunately I have no idea what it is !.

Any suggestions are welcomed.

You would probably get better results if you enable 1 capture at a time, stop timer1 before clearing it & entering CaptureLoop2.

Are you trying to measure the period or high-going pulse width?

Hi thanks for your reply

I am measuring the period of the incoming pulses.

I have to say I had not considered enabling one CCP at a time. Would I acheive this changing the CCPxCON statement? (x being 1 or 2). Such as CCP1CON = %00000000.

Thanks.

Quote:

Would I acheive this changing the CCPxCON statement?

Yes. Enable 1. Wait for capture. Disable 1, Enable 2, wait for capture, etc. It's a good idea to stop Timer1 before clearing it also.

Many thanks Bruce for your advice.

I have done as you have suggested, including stopping Timer1 (T1CON = 0) before clearing, and all appears to be operating as it should. I am a happy chappie.....

Once again many thanks. Sorted.....

Chris. :)