Button command question

I am using the 5 button commands to handle 5 push buttons in my application. No auto repeat is used, just a simple if pressed… then do… My software checks on each button in order or importance, and once it finds that one is pressed, it jumps out of the 5 button sequence and performs the necessary task. All this works very well.
Now my client requests that when 2 buttons are pressed simultaneously, something else is done. Can any one point me in the right direction to check for two of them pressed at once?

Hello aherrera,
Ok suppose you are using PortB as follows
'PortB.0 = switch 1
'PortB.1 = switch 2
'PortB.2 = switch 3
'PortB.3 = switch 4
'PortB.4 = switch 5
and you are doing If PortB.0 = 1 then . . .
the port has a binary value when you push a switch, port B.0 = 1, portB.1 = 2, both = 3
so you could use a select case statement or a lookup table to direct your code flow.

I am not checking every pin; I am using the button command so I can de-bounce the switches.

Quote:

---

Originally Posted by aherrera

I am not checking every pin; I am using the button command so I can de-bounce the switches.

---

Ok button command is overrated and too complicated.
i am not home and do not have the manual with me so bear with me if I error.

Code:

---

myVar var byte[5]
myVar.0 = portB.0
myVar.1 = portB.1
myvar.2 = portB.2
myvar.3 = portB.3
myvar.4 = portB.4

check:
if myVar != 0 then pause 50
if myVar != 0 then

select case myvar
case 0 goto check
case1  ' button1 pushed
do something . . . fish
case2  ' button2 pushed
do something . . .cut bait
case3 ' 2 buttons pushed
do another something . . . look for better lake
case 4 ' button3 pushed
. . .
case 7 ' 3 buttons pushed
do or not do you decide

case else
 goto check
end select
endif
else
goto check

---

some of the syntax may be incorrect above but it should steer you to what you are wanting

Thank you for your help, so, you think is over rated, I see you are de-bouncing by pausing, but this will cause the software to repeat the press if someone holds the button pressed, the button command takes care of all this.

Another idea.. sort of.

I do not think it is likely that two buttons will be pressed at the same time. So if the buttons are on the same port then read the port twice to see if the second one has been pushed.

Untested but something like

Code:

---

CHECK_BUTS:
BUTVAR = PORTB & $1F
IF BUTVAR >= 1 THEN CHECK2
GOTO CHECK_BUTS

CHECK2
PAUSE 50
BUTVAR = PORTB & $1F
SELECT CASE BUTVAR
'insert case statements
GOTO CHECK_BUTS

---

Hi,

BUTTON Command could be fine here ... let's suppose button tie pin to ground.

Code:

---


SCAN:

FOR I = 0 to 4

  BVar = 0

  BUTTON PORTB.0[I],0,255,0,BVar,1,Action

NEXT I

I =  255 ' just to allow CASE 0 ...

Action :

SELECT CASE I

    CASE 0 ...

...

    CASE ELSE  GOTO SCAN

END SELECT

---

As the debouncing do not occur if button is not pressed ( Mr de la Pallice )... scanning is very fast !

CQFD

Alain

For twin Button press ...

just add another scan loop ...

Code:

---



SCAN:

RESULT = 0

FOR I = 0 to 4

  BVar = 0

  BUTTON PORTB.0[I],0,255,0,BVar,1,Action

NEXT I

GOTO SCAN                                            ' No need to go further ...

Action :

      RESULT.I = 1                                    ' Store the first button pushed
     
      PAUSE 250                                        ' Let a little time for pushing the
                                                              ' next button ...
      FOR J= 0 to 4
 
      IF J = I THEN I = I+1                            ' Button already pushed !!! ... Skip test.
 
      BVar = 0

    BUTTON PORTB.0[I],0,255,0,BVar,1,Action2

    NEXT J

    GOTO Action1                                      ' Only one button Pushed  ...

   
Action2:

RESULT.J = 1                                              ' Store the second button pushed

Action1:

SELECT CASE RESULT

    CASE %00000001                      ' Button 0 alone
    ...
    CASE %00000010                      ' Button 1 Alone
    ...
    CASE %00000100                      ' Button 2 Alone
    ...
    ...
    ...
    CASE %00000011                      ' Buttons 0 and 1 ... or  1 and 0
    ...
    CASE %00000101                      ' Buttons 0 and 2 ... or  2 and 0
    ...
    ...
    ...
    CASE %00000110                      ' Buttons 1 and 2 ... or  2 and 1
    ...
    CASE %00001010                      ' Buttons 1 and 3 ... or  3 and 1
    ...
    ...
    ...
    CASE %00001100                    ' Buttons 2 and 3 ... or  3 and 2
    ...
    CASE %00010100                    ' Buttons 2 and 4 ... or  4 and 2
 
    CASE ELSE  GOTO SCAN

END SELECT

---

with 16 bits for RESULT, RESULT.Highbyte for I, RESULT.Lowbyte for J, .... you can even check in which order the buttons have been pushed ...

Too much ??? Ok, I take it back to my kangaroo pocket ...

Alain

I want to thank everybody for their great help. I think I have enough to get me going here...

Arrrgh !!!

a little typing bug :

Code:

---

  IF J = I THEN I = I+1                            ' Button already pushed !!! ... Skip

---

should have been

Code:

---

  IF J = I THEN J = J+1                            ' Button already pushed !!! ... Skip

---

as everybody did notice ...

Alain