P1c18f26k20-internal clock set up fail -64mhz

[MINHLE]

HI,
I TRY to set up to run the osc internal @64Mhz, but fail.

conf_1H: FOSC_INTIO67 (or FOSC_INTIO7) ;OTHER config's of 1H are off
OSCCON = $70 (16MHZ selected)
OSCTUNE = $40 (enable PLL)

the output @portb.6 fail (no power)-and data out from other pins runs fast

OSCTUNE =$40 {omitted)
data out from portb runs well, but slow and low power @ output

i also try to set OSCTUNE TO $CF, maximum frequency and PLL enable, but portb.6 still lost power
so what wrong?
any help i do appriciate
tks in ad.

[richard]

try osccon.1 =1
failing that post your code and tell us what version of pbp you are using

[EarlyBird2]

This could help.

7406

OSCCON 6:4 need setting for 16 MHZ which is $70, which is what you have.
OSCTUNE 6 needs setting to connect internal oscillator to 4xPLL $40, which you have.

Looking at the Internal Oscillator Block OSCCON 1:0 have an effect and from the datasheet.

bit 1-0 SCS<1:0>: System Clock Select bits
1x = Internal oscillator block
01 = Secondary (Timer1) oscillator
00 = Primary clock (determined by CONFIG1H[FOSC<3:0>]).

which tells me, if I understand correctly, that OSCCON 1 needs setting. Which is what Richard said.

Which now makes OSCCON $72.

Last there is config1H for HSPLL and HFINTOSC/PLL

_FOSC_HSPLL_1H EQU H'F6' ; HS oscillator, PLL enabled (Clock Frequency = 4 x FOSC1)
_FOSC_INTIO67_1H EQU H'F8' ; Internal oscillator block, port function on RA6 and RA7
_FOSC_INTIO7_1H EQU H'F9' ; Internal oscillator block, CLKOUT function on RA6, port function on RA7

which I leave to you or others to explain, I use boot loader and never used configs.

[MINHLE]

THANSKS alot for your help.

yes, i try

OSCCON = $72,
OSCTUNE = $40
the problem still persises.
portb.6 lost power. but it runs faster
-------------------------------------------------------------------------------
here is the conf.
__CONFIG _CONFIG1H, _FOSC_INTIO7_1H & _FCMEN_OFF_1H & _IESO_OFF_1H
__CONFIG _CONFIG2H, _WDTEN_ON_2H & _WDTPS_512_2H' __CONFIG _CONFIG3H, _CCP2MX_PORTC_3H & _PBADEN_OFF_3H & _LPT1OSC_OFF_3H & _HFOFST_ON_3H & _MCLRE_ON_3H
__CONFIG _CONFIG4L, _STVREN_ON_4L & _LVP_OFF_4L & _XINST_OFF_4L
OSCCON = $72,
OSCTUNE = $40
-----------------------------------------------------------------------------
portb = 0
latb = 0
trisb = 0
----------------------------------------------------
about the SCS it is automatic set to 00- becasue in the CONFI_1h --- FOSC_INRIO67- (IT IS determined by primary osc in the 1H line)
here is the explaination in the data sheet
------------------------------------------============
2.9.1 SYSTEM CLOCK SELECT
(SCS<1:0>) BITS
The System Clock Select (SCS<1:0>) bits of the
OSCCON register select the system clock source that
is used for the CPU and peripherals.
• When SCS<1:0> = 00, the system clock source is
determined by configuration of the FOSC<2:0>
bits in the CONFIG1H Configuration register.
• When SCS<1:0> = 10, the system clock source is
chosen by the internal oscillator frequency
selected by the INTSRC bit of the OSCTUNE
register and the IRCF<2:0> bits of the OSCCON
register.
• When SCS<1:0> = 01, the system clock source is
the 32.768 kHz secondary oscillator shared with
Timer1.
After a Reset, the SCS<1:0> bits of the OSCCON
register are always cleared.
-----------------------------------------------------------
the version, of pbp. it is 2.6c
i read the post of: http://www.microchip.com/forums/m730158.aspx-
also mentioned the same issue- but the PLLCFG is not recognized in the PBP

thanks for your concern,
regards

[richard]

try a __CONFIG _CONFIG4L, _DEBUG_OFF in your configs

as henrik wrote yesterday in a similar post the config option's syntax can be found in the pic18f26k20.inc file in your relevant version mpasm directory

[richard]

interestingly there is a PLLCFG = ON in the pbp3 device reference config options


look like a _PLLCFG_ON_1H is what you need

[MINHLE]

HELLO,
thanks for your guide,
YES i try & _DEBUG_OFF_4L

OSCCON = $72 (OR $70)
OSCTUNE = $40
PROBLEM PERSIS (slow)
i will see the inc directory of mpas
is it effected by the hc595?
i found that its max freq. is 25MHz
however, i test the 595 runs well @40mhz

thanks a gain for your contribution
regards

[EarlyBird2]

i read the post of: http://www.microchip.com/forums/m730158.aspx

Very interesting thanks.

Yes one of the settings that worked in the above link is.

__CONFIG _CONFIG1H, _FOSC_INTIO67_1H
OSCCON = $70
OSCTUNE = $40

Is that not what you started with?

[MINHLE]

Y]hello,

yes the above is work.
..
osccon = $70 or (60)
osctune = $40

for single leds
i move to drive 595 then there r problem- lost power or low speed @ out put

now i try to clean the pbp to see waht happen'

thenak for your help.
regards

[MINHLE]

HI ALL,

the pic run well @ 4mhz ,HSPLL; 8, 10mhz ... problem (HSPLL).

the conf. remains unchanged

__CONFIG _CONFIG1H, _FOSC_HSPLL_1H & _FCMEN_OFF_1H & _IESO_OFF_1H
__CONFIG _CONFIG2H, _WDTEN_ON_2H & _WDTPS_512_2H
__CONFIG _CONFIG3H, _CCP2MX_PORTC_3H & _PBADEN_OFF_3H & _LPT1OSC_OFF_3H & _HFOFST_ON_3H & _MCLRE_ON_3H
__CONFIG _CONFIG4L, _STVREN_ON_4L & _LVP_OFF_4L & _XINST_OFF_4L & _DEBUG_OFF_4L

where is the problem?
thanks all for your help
regards

[richard]

minhle
quite a lot here seems to be lost in the translation somehow


the output @portb.6 fail (no power)-and data out from other pins runs fast
what does this mean ?


the conf. remains unchanged

__CONFIG _CONFIG1H, _FOSC_HSPLL_1H & _FCMEN_OFF_1H & _IESO_OFF_1H
__CONFIG _CONFIG2H, _WDTEN_ON_2H & _WDTPS_512_2H
__CONFIG _CONFIG3H, _CCP2MX_PORTC_3H & _PBADEN_OFF_3H & _LPT1OSC_OFF_3H & _HFOFST_ON_3H & _MCLRE_ON_3H
__CONFIG _CONFIG4L, _STVREN_ON_4L & _LVP_OFF_4L & _XINST_OFF_4L & _DEBUG_OFF_4L

have you now changed to using an external xtal ?


i move to drive 595 then there r problem- lost power or low speed @ out put

what is a 595 ? do you mean a 74hc595 ?
if so a "595" can clock in data @100mhz which will be at least 10x greater than a bit banged routine could achieve even at 64mhz clock


can I suggest you just try to "blink a led" on say portb.6 and see if it blinks at the correct rate , if not then post your complete code for further evaluation

[EarlyBird2]

the conf. remains unchanged

__CONFIG _CONFIG1H, _FOSC_HSPLL_1H & _FCMEN_OFF_1H & _IESO_OFF_1H
__CONFIG _CONFIG2H, _WDTEN_ON_2H & _WDTPS_512_2H
__CONFIG _CONFIG3H, _CCP2MX_PORTC_3H & _PBADEN_OFF_3H & _LPT1OSC_OFF_3H & _HFOFST_ON_3H & _MCLRE_ON_3H
__CONFIG _CONFIG4L, _STVREN_ON_4L & _LVP_OFF_4L & _XINST_OFF_4L & _DEBUG_OFF_4L

where is the problem?
thanks all for your help
regards

The conf. has changed from #4


here is the conf.
__CONFIG _CONFIG1H, _FOSC_INTIO7_1H & _FCMEN_OFF_1H & _IESO_OFF_1H
__CONFIG _CONFIG2H, _WDTEN_ON_2H & _WDTPS_512_2H' __CONFIG _CONFIG3H, _CCP2MX_PORTC_3H & _PBADEN_OFF_3H & _LPT1OSC_OFF_3H & _HFOFST_ON_3H & _MCLRE_ON_3H
__CONFIG _CONFIG4L, _STVREN_ON_4L & _LVP_OFF_4L & _XINST_OFF_4L

also you said



yes the above is work.
..
osccon = $70 or (60)
osctune = $40

for single leds
i move to drive 595 then there r problem- lost power or low speed @ out put

If it works for single leds then it works and all of your code needs checking. So please post your code so we can help.

[MINHLE]

HI,
thanks for your help.
i suspect st wrong,
i test the whole port b. it runs well (8 leds) - FOSC_INTIO67 (16x4mhz)
However, when attaching portb to the 74hc595 - then 1 of the port pin lost power.
just last week, the system run well @40mhz. (external osc).
now problem is data to send out is not right
i will spend 1 more time to check, and will send the program to you

regards

[richard]

when attaching portb to the 74hc595 - then 1 of the port pin lost power.
I'm not really sure what this means , its rather ambiguous
perhaps a schematic diagram (or a photo) of your setup would be in order

[MINHLE]

HI,,
thANKS A LOT RICHARD,

I MOVE TO USE 18F4620, THE PREVIOUS CONF. IS FINE (internal osc*4 = 32 mhz)
the program runs well @40mhz (external osc) then there are problems
i.e. data output randomly- (due to dirty breadboard)
line appears on the screen (same cause above).
i will going back to see the 18f26k20.next week.

thanks again
regards

[Demon]

As requested by others, post your complete code and a schematic of your circuit.

Have you disabled analog features on any pins you use as digital?

Robert

[MINHLE]

HI ALL
THANKS for all
the program actually runs well, but the pause time is not correct and the current supply is not adequate ( due to dirty breadboar...)

at high frequency, some of the port pins is measured = 0, (when the port drives other ic) look like there is no power at all.
the set up is right:

_FOSC_INTIO67_1H
OSCTUNE = $40
OSCCON = $70

the PBADEN = OFF, so the portb is digital I/O
thanks a gain for all

regards