2x16 LCD doesn't show values, please help

[s.triker]

Hi all,

I'm trying to drive my LCD module (2x16 ATM1602B with driver S6A0069) from PIC16F88. I spent 2 days on this, but I can't display any character on LCD. I checked connections many times, it is correct.

Only thing I see is the first line containing blank squares. I've read several post with this topic, and it seems to be a problem with LCD init.

I tried the same code and circuit in Proteus and it works perfectly. But in real nothing .

Does anyone have an idea how to initialize LCD properly in PicBasic pro? Or if you see any other error please let me know.

My connections are:
D4-D7 .... RB0-RB3
RS ......... RB4
E ........... RB5
RW ........ Ground
Vo ........ Pot against Ground (approx 0.8 V)

@ DEVICE INTRC_OSC_NOCLKOUT & WDT_OFF & PWRT_OFF & MCLR_OFF & BOD_ON & LVP_OFF & PROTECT_OFF
             
' Define LCD registers and bits
DEFINE LCD_DREG PORTB
DEFINE LCD_DBIT 0
DEFINE LCD_RSREG    PORTB
DEFINE LCD_RSBIT    4
DEFINE LCD_EREG PORTB
DEFINE LCD_EBIT 5
DEFINE LCD_BITS 4
DEFINE LCD_LINES    2
DEFINE LCD_COMMANDUS    2000 
DEFINE LCD_DATAUS   50 ' 1000 

DEFINE OSC 4

OSCCON = %01100110 ' internal 4MHz
OPTION_REG = $7f  
ANSEL = 0     
CMCON = 7   

FLAGS = 0

    Pause 500       ' Wait for LCD to startup

mainloop: 
    Lcdout $fe, 1   ' Clear LCD screen
    Lcdout "Hello"  ' Display Hello
    Pause 500       ' Wait .5 second
    
    Lcdout $fe, 1   ' Clear LCD screen
    Lcdout "World"
    Pause 500       ' Wait .5 second
    
    Goto mainloop   ' Do it forever

I would appreciate any help,
many thanks,
regards,
Paul

[mackrackit]

Is your chip running? Can you blink an LED at the expected rate?
What is your OSC setup?

And never trust a sim..
http://www.picbasic.co.uk/forum/show...9313#post99313

[s.triker]

Hi Dave,

I'm not sure I understand you correctly. Chip is running, I put LED on all data pins D4-D7 and R/S as well and it blinks 0.5s interval (some of them didnt blink, just keeped HIGH). I also tried to start-up PIC later than LCD to get LCD powered properly, but still the same.

I use internal oscillator on 4MHz. This is the first time I use LCD, so please excuse some misunderstandings.

Thank you,
Pavel

[mackrackit]

ok.
Try disabling the pull ups and play with the contrast.

[Plcguy]

I think Dave means put an LED on a pin and drive it on before the LCD statement and a pause of 1 second and off after the LCD statement and a 1 second pause.
With this you know the processor is running AND at the correct speed (if it flashes for 1 second)

[s.triker]

Hi guys,

ok, thank you, I will test it and let you know. Unfortunately, I'm not able to program the PIC now, it seems my JDM programmer failed .
I have to fix it and let you know.

Many thanks,
Paul

[s.triker]

Hi,

success !!
Finally LCD shows values. I had to use external 4MHz crystal with 33p capacitors connected to ground. I also tried to tune OSCCAL settings, but without success. Now LCD shows what I want.

Thank you very much,
Paul