Transformerless Power Supply of 1A at 5Volts!


Closed Thread
Results 1 to 23 of 23
  1. #1
    Join Date
    Nov 2003
    Location
    Greece
    Posts
    3,793

    Default Transformerless Power Supply of 1A at 5Volts!

    The topic of P.S. direcly from the mains is very dangerous and I do not recommed to do so.

    But there are cases that this is unavoidable.

    Current designs have the dis-advatage that are of low current.

    The attached one is a clever design from Elektor and gives about 1A at 5Volts.

    I repeat that all parts are live and should never be touched!

    Ioannis
    Attached Images Attached Images  

  2. #2
    Join Date
    Jan 2009
    Location
    Miami, Florida USA
    Posts
    637


    Did you find this post helpful? Yes | No

    Default

    Ioannis,

    Unless I am missing something here, K1 in your schematics seems to be a transformer. The datasheet for the LM2595 gives a maximum input voltage for this chip of 40V. If K1 is not a transformer, it looks like you would fry this chip with a power supply input of 230Vac.

    Robert

  3. #3
    Join Date
    Nov 2003
    Location
    Greece
    Posts
    3,793


    Did you find this post helpful? Yes | No

    Default

    Robert.

    K1 is a connector!

    As for the 2595, yes you are right on the max input voltage. BUT, look carefully at the schematic.

    The 2595 will get a max of 40 volts and nothing more than this. Zener, T1 and T2 will make sure that it stays in safety region.

    Thats why I stated that the circuit is clever.

    Ioannis

  4. #4
    Join Date
    Jan 2009
    Location
    Miami, Florida USA
    Posts
    637


    Did you find this post helpful? Yes | No

    Default

    Ioannis,

    Yes, you are right about T1 and T2 keeping the voltage low on the LM2595 chip. However, I am still not convinced with this circuit. After looking at the datasheet for T2, it seems to me like the Drain and the Source inputs should be swapped for a proper grounding on LM2595. The current should be flowing away from the ground in LM2595, not towards it.

    Also, the maximum VGS voltage on T2 is 20V, so if for some reason T1 fails T2 would also be fried. I don't know why Elektor designed this circuit without a transformer, and I agree with you that this is very dangerous.

    Robert

  5. #5
    Join Date
    Nov 2003
    Location
    Greece
    Posts
    3,793


    Did you find this post helpful? Yes | No

    Default

    Technically the circuit is correct. No need for pin swaping. It is OK as it is.

    At first I know it is a bit confusing but trust me it is very clever trick.

    The purpose of zener and the 2 transistors is to let the voltage raise up to say 40 volts on the capacitor and 2595 input. Then T1 is biased and switches off T2 so that the raising voltage cannot hurt the 2595.

    This is repeated again on the next half period.

    As for the dangerous this refers to the live voltages all over the circuit and the circuits connected to this. Other than this I consider it "safe" in a matter of speaking to use it.

    Ioannis
    Last edited by Ioannis; - 8th December 2010 at 23:42. Reason: Typos

  6. #6


    Did you find this post helpful? Yes | No

    Wink Microchip has examples...

    The Microchip website has examples of running micros off the AC line... search the app notes...

  7. #7
    Join Date
    Nov 2003
    Location
    Greece
    Posts
    3,793


    Did you find this post helpful? Yes | No

    Default

    Not at 1A though...

    Ioannis

    Quote Originally Posted by mtripoli View Post
    The Microchip website has examples of running micros off the AC line... search the app notes...

  8. #8
    Join Date
    Nov 2009
    Location
    London
    Posts
    251


    Did you find this post helpful? Yes | No

    Question

    I know some places have extreme voltage drop. Will this circuit work if AC voltage drops to lets say 160V from 230V & also if it rises to Lets say 300V from 230 V? Thanks

  9. #9
    Join Date
    Jan 2006
    Location
    Istanbul
    Posts
    1,185


    Did you find this post helpful? Yes | No

    Default

    Quote Originally Posted by Megahertz View Post
    I know some places have extreme voltage drop. Will this circuit work if AC voltage drops to lets say 160V from 230V & also if it rises to Lets say 300V from 230 V? Thanks
    In what place of earth can municipal power lines go from 230V to 300V?

    I can understand 240 or even at max 260, but 300? Such a case would end up for compensation in court.

    -------------------------
    "If the Earth were a single state, Istanbul would be its capital." Napoleon Bonaparte

  10. #10
    Join Date
    Nov 2003
    Location
    Greece
    Posts
    3,793


    Did you find this post helpful? Yes | No

    Default

    The circuit will work from say 10 Volts AC up to whatever the rated voltage of the componets used is, mainly the bridge.

    So the answer is yes.

    Ioannis

  11. #11
    Join Date
    Aug 2006
    Location
    Look, behind you.
    Posts
    2,818


    Did you find this post helpful? Yes | No

    Default

    Quote Originally Posted by sayzer View Post
    In what place of earth can municipal power lines go from 230V to 300V?

    I can understand 240 or even at max 260, but 300? Such a case would end up for compensation in court.

    -------------------------
    Hi Sayzer,
    Probably depends upon how you measure it. If you use an a/c voltmeter then it is calibrated in RMS and gives accurate results. If he is using a D/C voltmeter and a diode, then he is seeing peak voltage - diode drop, and will see an inaccurately high value.
    If you do not believe in MAGIC, Consider how currency has value simply by printing it, and is then traded for real assets.
    .
    Gold is the money of kings, silver is the money of gentlemen, barter is the money of peasants - but debt is the money of slaves
    .
    There simply is no "Happy Spam" If you do it you will disappear from this forum.

  12. #12
    Join Date
    Nov 2009
    Location
    London
    Posts
    251


    Did you find this post helpful? Yes | No

    Default

    The country in question is India. When I was there, I actually saw the voltage drop upto 170V and during power faliure when the backup generators were fired up, voltage at few places seem to be as high as 280-300V and so I asked the question just to have the knowledge
    Thanks

  13. #13
    Join Date
    Nov 2003
    Location
    Greece
    Posts
    3,793


    Did you find this post helpful? Yes | No

    Default Re: Transformerless Power Supply of 1A at 5Volts!

    The circuit of Elektor will NOT work when input voltage is rising above 39 or so volts. So it will work perfectly well if input AC voltage is just up to 110. No need to change anything, or almost anything. May be just the R5 changed to a lower value, say 15 ohms.

    The circuit is very clever and the SMPS is disabled by the pass transistor wheninput voltage is greater than 39 so volts. Beware it is not isolated.

    Ioannis

  14. #14
    Join Date
    Nov 2013
    Posts
    1


    Did you find this post helpful? Yes | No

    Default Re: Transformerless Power Supply of 1A at 5Volts!

    Did anyone try to build this circuit? Can this work at 230v AC

  15. #15
    Join Date
    Nov 2003
    Location
    Greece
    Posts
    3,793


    Did you find this post helpful? Yes | No

    Default Re: Transformerless Power Supply of 1A at 5Volts!

    It is mainly for 230 VAC

    Ioannis

  16. #16
    Join Date
    Nov 2013
    Posts
    7


    Did you find this post helpful? Yes | No

    Default Re: Transformerless Power Supply of 1A at 5Volts!

    It is not AC but rectified AC to result in DC. Also note the Zener that drops the voltage.

  17. #17
    Join Date
    Nov 2003
    Location
    Greece
    Posts
    3,793


    Did you find this post helpful? Yes | No

    Default Re: Transformerless Power Supply of 1A at 5Volts!

    Please review the circuit more carefully. The circuit works from zero up to about 39 volts. After that point it cuts off.

    It works very good from 230 VAC.

    Ioannis

  18. #18
    Join Date
    Feb 2004
    Location
    Michigan, USA
    Posts
    305


    Did you find this post helpful? Yes | No

    Default Re: Transformerless Power Supply of 1A at 5Volts!

    Be interesting to see what happens from 90Vac to 304Vac.

  19. #19
    Join Date
    Jan 2005
    Location
    Montreal, Quebec, Canada
    Posts
    2,585


    Did you find this post helpful? Yes | No

    Default Re: Transformerless Power Supply of 1A at 5Volts!

    Agreed, I'd be interested in 110VAC range.

    Robert

    Edit: Did you guys check Melanie's design?

    http://www.picbasic.co.uk/forum/show...7531#post17531
    Last edited by Demon; - 13th December 2013 at 00:36.

  20. #20
    Join Date
    Nov 2003
    Location
    Greece
    Posts
    3,793


    Did you find this post helpful? Yes | No

    Default Re: Transformerless Power Supply of 1A at 5Volts!

    Quote Originally Posted by jmgelba View Post
    Be interesting to see what happens from 90Vac to 304Vac.
    As I said it does not do anything above 39 or so volts. So where is the problem?

    After the sine wave has reached the 38-39 volts the circuits is not powered any more from the power line.

    Ioannis

  21. #21
    elipee's Avatar
    elipee Guest


    Did you find this post helpful? Yes | No

    Default Re: Transformerless Power Supply of 1A at 5Volts!

    Very interesting circuit, however, a think it is not going to work very well, look at T2 ( BUZ41A or IRF730) , both have a maximum 20V VGS, so when voltage get bigger than 20 , T2 gate get damage. Maybe it work for a time, but T2 VGS is out of specification.

  22. #22
    Join Date
    Nov 2003
    Location
    Greece
    Posts
    3,793


    Did you find this post helpful? Yes | No

    Default Re: Transformerless Power Supply of 1A at 5Volts!

    It won't get that high for long time to destroy the Mosfet. Also the Zener is not a switch but it does start to operate at lower that rated voltage.

    It does work with great success and efficiency.

    If you are concerned about Vgs, there are other Mosfets (sure more expensive) to replace this one.

    Ioannis
    Last edited by Ioannis; - 27th December 2015 at 11:12.

  23. #23
    Join Date
    Sep 2014
    Posts
    2


    Did you find this post helpful? Yes | No

    Default Re: Transformerless Power Supply of 1A at 5Volts!

    "voltage at few places seem to be as high as 280-300V"

    No so.

    Do you realise the current taken by a globe (and lots of other devices) will increase considerably as the voltage increases. When the voltage rises by say 10%, the current will rise by much more than 10% and this will put a very heavy burden on the generator and in most cases the generator will not be able to supply the load. This is why the voltage will not rise as you have stated.
    Globes and radiators are not linear devices, but if they were, a 1,000 watt radiator at 250v would take 1250 watts at 280v. This is 25% increase in wattage for 13% increase in voltage.
    The figures would be much higher for 230v supply.

Similar Threads

  1. Transformerless Power Suppply
    By ERIK in forum Schematics
    Replies: 75
    Last Post: - 3rd September 2012, 16:08
  2. PIC backup power supply: switchover ???
    By xnihilo in forum mel PIC BASIC Pro
    Replies: 13
    Last Post: - 18th April 2008, 18:05
  3. Transformerless Power supply
    By nikhil in forum mel PIC BASIC Pro
    Replies: 1
    Last Post: - 17th January 2007, 08:07
  4. Replies: 10
    Last Post: - 16th October 2006, 19:23
  5. Transformerless Power Supply
    By volkov in forum General
    Replies: 15
    Last Post: - 3rd July 2006, 00:13

Members who have read this thread : 1

You do not have permission to view the list of names.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts