Search Results - MEL PICBASIC Forum


Search:

Type: Posts; User: mombasa; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    1,160

    Re: e32 rx/tx module usage

    hi, in these days I am working on a temperature sensing project with data transmission through an E32915T30D and a receiver of the same type. I am using an 18f252 and a DS18B20 as a sensor. As soon...
  2. Replies
    2
    Views
    616

    big char oled display

    I recently used a .96 inch oled display driven with i2c. The characters are very small and difficult to read. Has anyone implemented big characters for this type of display? Thank you
  3. Replies
    4
    Views
    1,715

    Re: e-paper/ e-ink display

    Demon thanks for the suggestion. I'll try to do something.
  4. Replies
    4
    Views
    1,715

    Re: e-paper/ e-ink display

    thanks for the reply. I would like to use these pbp displays. I was looking for someone with experience. Thanks

    https://www.sparkfun.com/datasheets/LCD/Monochrome/WATN001002BFW00000000.pdf...
  5. Replies
    4
    Views
    1,715

    e-paper/ e-ink display

    Hi, did anyone have to use e-paper displays with pbp? Thanks
  6. Thread: sorting array

    by mombasa
    Replies
    3
    Views
    1,845

    Re: sorting array

    Richard thank you very much for your time you spent for me. Your solution is complex for my knowledge. However, I will analyze it carefully. You did a lot more than I asked for. I'll let you know the...
  7. Thread: sorting array

    by mombasa
    Replies
    3
    Views
    1,845

    sorting array

    Hi, i would need help to solve a problem. I have 9 variables that contain the penalties found in a car race. I have to put them in ascending order and form a ranking by keeping the variable name or...
  8. Replies
    2
    Views
    1,929

    Re: unexpectedly reset

    Henrik thanks for your help. I discovered that I had started many GOSUB inside of GOTO and never found its RETURN. The stack had too many "orphaned" address "and then the micro doing strange things,...
  9. Replies
    2
    Views
    1,929

    unexpectedly reset

    For my project I'm using a 18F4525 (48k.) With PBP3. I will use only 31k but the micro resets itself after a few minutes of operation. Pin 1 is permanently connected to the positive. WDT disabled. ...
  10. Thread: Error Messages

    by mombasa
    Replies
    4
    Views
    1,690

    Re: Error Messages

    Henrik thanks for your help and for your time. Regards
  11. Thread: Error Messages

    by mombasa
    Replies
    4
    Views
    1,690

    Re: Error Messages

    Thanks Henrik, you were right, if I disable LONGs is all ok. The problem is that I need both functions. Do you think there is no solution?
  12. Thread: Error Messages

    by mombasa
    Replies
    4
    Views
    1,690

    Error Messages

    I'm now using Picbasic Pro 3.0.6.1. When I INCLUDE "LCDbar_INC.bas", I have this error messages:

    Macro DIV32?WW not found in marco file
    Macro DIV32?CW not found in macro file

    can help...
  13. Replies
    5
    Views
    2,139

    Re: Optimize eeprom capacity

    Thanks Henrik, your solution seems like a good starting point .
  14. Replies
    5
    Views
    2,139

    Re: Optimize eeprom capacity

    Unfortunately I have to change the program of a Pic with EEPROM and I have to add more data . I could insert another EEPROM but I should change almost one hundred printed circuit boards. I think it...
  15. Replies
    5
    Views
    2,139

    Optimize eeprom capacity

    Hi, I have some eeprom locations where I store information as possible . For example, I read the contents of four memory locations , I transfer it on four variables for a total of 32 bits. Now I...
  16. Replies
    6
    Views
    1,831

    Re: Number conversion

    Thanks to all for the invaluable assistance :D
  17. Replies
    6
    Views
    1,831

    Re: Number conversion

    Thanks Demon, maybe I have not explained well, but I have a number of hours expressed as a decimal (eg. 2.5h - 4,23h - 1,125h) and I need to convert this number in hours: minutes: seconds (HH: MM :...
  18. Replies
    6
    Views
    1,831

    Number conversion

    I need to convert some numbers that express time values ​​from decimal to sexagesimal . Does anyone have a valid formula ? thanks
  19. Replies
    11
    Views
    3,348

    Re: A strange problem

    Thanks Acetronics, you did a great job. RTFM is the answer.
  20. Replies
    11
    Views
    3,348

    Re: A strange problem

    Thank you for your interest, but I do not understand is that I have used this statement thousands of times with the 18F252 that I used before. Now I'm in trouble because I need to show the value of...
  21. Replies
    11
    Views
    3,348

    Re: A strange problem

    No, it is so, even this statement "LCDOUT $FE,$80,DEC A" does not work.
  22. Replies
    11
    Views
    3,348

    Re: A strange problem

    Thanks tasmod, with this statement "LCDOUT $ FE, $ 80, # A" now everything seems to work ok. But what has changed? I have always used "DEC A" and has always worked. What is the problem? Thank you...
  23. Replies
    11
    Views
    3,348

    A strange problem

    Since storage requirements for the 18F252 I left and walked to get on 18f2620 lcd dsplay question marks instead of the value of variables that I use. This problem only affects the contents of...
  24. Replies
    4
    Views
    2,025

    Re: A stopwatch to improve

    Sorry Alain but I use in my stopwatch a ds32khz chip that drives the Timer1, and a crystal of 4 MHz for the 18f252. I believe that the 'elapsed timer using also a crystal of 4 MHz for the pic and 4...
  25. Replies
    4
    Views
    2,025

    A stopwatch to improve

    For my stopwatch I need a precision of a hundredth of a second. By using a 18f252 Timer1 driven by a quartz to 32768 hz, I try to get an interrupt every 10 ms that I should increase a variable, but I...
Results 1 to 25 of 41
Page 1 of 2 1 2