Hi
Thanks for the char handling
thisone is working perfectly
hserout ["rg", 13]
Hserin 1000, start, [STR char\4\$06] ' Get a char from serial port
pause 10
if char[0] = $30 then
Type: Posts; User: RFsolution; Keyword(s):
Hi
Thanks for the char handling
thisone is working perfectly
hserout ["rg", 13]
Hserin 1000, start, [STR char\4\$06] ' Get a char from serial port
pause 10
if char[0] = $30 then
Thanks aerostar
something like this:
get_key:
hserout ["rg", 13]
Hserin 1000, start, [STR char\4\$06] '
pause 10
Hi all
I'm trying to interface a serial LCD by byvac with keypad via HSERIN/OUT
http://www.byvac.com/index.php/BV4619
but have the following problem
If I want to read a "keypress" ,following...
Hi Robert, yess this is the side where the sensor and lego code is comming from
Hi
I build the following wire guidance sensor succesfully
http://www.philohome.com/sensors/filoguide/filoguide-schem.gif
I removed the D4,D5,D6 part and put a pullup to +5V on the collector...
Hi
I would like to make a menu where I can setup a calibration table for a voltage read from the ADC from a non linair RF power detector
example:
Power is 10W (RF power) detected by an RF...
Hi all
I'm measuring a voltage from an RF power detector which is not linear with an 8bit ADC (if possible later with 10bit)
I would like to display the coresponding power level on an lcd based...
Thanks, I took a look and ordered a few to test, as the wire is buried I need to detect it at a distance of 10-20cm, I'm thinking to install 2 sensors about the same distance and then use 2 ADC's
...
Hi Comwarrior
thanks for your information,
I will have a look for analog Hall sensors, never used them
Ofcourse with the LC coil detector like lego mindstorm, i can feed both detetor voltage...
Hi All,
I think this might be a very interesting topic for all robot builders
I have build a prototype robot with 2 DC motors controlled by a dual H-bridge controlled by I2C
...
Hi
I try to use a 16F88 with mplab as compiler, i want to use mclr as I/O and the internal oscilator
but i'm getting an error:
error 118 ..... overwriting previous address contents (2007)...
Hi
Well you are right,
is it possible to use LCDOUT in a way that D4-D7 of the LCD or not 4 I/O ports in a row
as I need all the ADC's portA is not an option
unfortunatly RX and TX from...
Hi all
I was wondering if it will be possible to use the following pin configuration
RB0-RB3 as LCD D4-D7
RA6,RA7 as E,RS
RA0-RA4 (AN0-AN4) as 10bit ADC
RB6,RB7 (AN5,AN6) as 10bit ADC
Hi all
First of all thanks for the reply's
I'm measuring 28.2 uS periode for the clock going to the DAC7611
Hi all
I have an excisting piece of hardware which is controlling a 12bit DAC7611
The DAC 7611 gets the clock from the excisting hardware,Data and Load/ , CS/ is wired low,
CLR/ is wired high...
Well the device is a 16F877 which talks to a DAC7611, i have no access to the 16F877 software and would like to use the data (value) send to the DAC in another circuit
So i want to read what the...
Hi
I have a hardware situation where I need to read a 12bit serial output
clocked by his own clock
If i'm right all Shiftin commands generates an own clock signal
is there a way to use an...
Hi Ioannis,
Thanks for your reply, maybe I expressed myself bad.
The excisting circuit is talking to the DAC7611, and i would like to get the information/value send to the DAC, with a small MCU...
Hi all,
I have an excisting hardware which is using a DAC7611 digital to analog converter
I would like to read the LD,SDI,CS/,CLK with a 16F876 and get the DAC 12bit value in a variable.
...
Hi Darrel,
Thanks a lot this is working perfect
Imagine if I would like to do the opposite
so from a 10 or 12bit value (representing 1 revolution) to deg.xx
Can you put me on the right...
Hi all
I have a decimal readout from a device which is giving me
a 16bit value (65535) for 1 resolution (360 deg)
I want to enter serially degrees.xx and convert this to a 16 bit value and...
Yes i the past I used and use siteplayer
but as it is only UDP i think it might be possible in an MCU directly
Hi all
I have a project where I have several ADC's and I/O which I now control by RS232
just a string send out with all ADC values.
I was wondering if it will be possible to send UDP packets...
Nice
Wondering what you are building for the WII ?
Hi,
I'm trying to measuring RF power with a directional coupler,followed by a schotky detection diode.
It gives me a voltage proportional to the power
On my LCD I would like to display...