Search:

Hello Bruce

tonyfelloni said that it must use the hardwareUart from the pic. I not understand why.
Perhaps a buffer problem why it not function with SoftUart?
The modul hande up to 64 bytes, is...

Hi tonyfelloni

I will get 2 pieces to test it and if i have problems to run it i ask for your help

Thank You

Best regards
Pedro

Hello tonyfelloni

I look for a similar wireless solution. What you say about this moduls? Work´s good? It's hard to use it? Have you a sample code that works that you can share?

Thanks
Best...

Thanks again Darrel

Regards

Pedro :)

Hello Darrel
Thank you for the sample

Can you explain this?
For Idx = 15 to 0 STEP -1 ; loop thru the bits

is this correct?
IF dat.0(Idx) THEN

why not

Hello Darrel

Have you a code example how to do that with the For / Loop
For beginners it helps a lot

Regards
Pedro

Hello rmteo
Not advantage, but you can't use a capacitve keyboard for blind people, in that case the capacitive sensing is not usable

Regards
Pedro

Hello

Capacitive sensing is another story, for that exists ic's from Quantum that work very well. Inductive sensing is more complex, then you must prepair
the painel mechanical with a few...

Hello

It depends what you want doe. For many years i wrote all my programs in PBP Pro and all work fine. For a new project that i need use spi, sd card with FAt32, Color TFT, RTC and Temperatur i...

Hello Kamikaze47

The link works. Try to copy the url to your web browser and start from that

Regards
Pedro

Hello BCD

Are you shure that Instant Interrupt is needed? Can you understand the
postet code in C from Microchip and make a PBP Pro sample from that?

Regards
Pedro

Hello All

Microchip have the new mTouch sensing inductiv detection on
http://www.microchip.com/stellent/idcplg?IdcService=SS_GET_PAGE&nodeId=2694&param=en538309

that can be done with any PIC...

Hi Jumper
You are right, i don't need to use the Timer

Thanks

Regards
Pedro

Hello Jumper

I have two Jumpers that i read at power up to choose four possible timings
16 seconds, 18, 19 and 20 seconds
I want use on the PIC 12F509 the internal 4Mhz oscilator

Best Regards...

Hello

I want to use the PIC 12F509 to monitoring one impuls in a Timewindow from 0 to 16 seconds, that means on power up a Timer starts and if i not receive one impuls until 16 seconds the...

Thank You

Regards
Pedro

Hello

I use since 2 years 18F452 and need now to migrate to 18F4520 "cheaper"
I use PortA and PortE as digital inputs and have in my code ADCON1 = $07
Must i change anything in my code when i...

Hello Aratti

Can´t use it with springs, the glasspanel must mounted fixed with no movement.
It must exist another possibility, but no idea?

Regards
Pedro

Hello mackrackit

I must design the "virtuall buttons" on the glass and the pcb is mounted behind, that is the problem than with normal capacitor sensor with the PIC
or Quantum IC's when a blind...

Hello

I look for a similar sensor solution "capacitive or inductive sensor".
My problem is it must usable for blind people too, to scan the area with the finger where the "Virtuall buttons" is,...

Hello

Exists a drivers to read and write to a sd card with pic controller like the AVR-DOS for the avr controller?

Thanks

Regards

Pedro

Hello
For a Atmel controller is this the configuration for the SPI to communicate to a lcd and it works very good.

Using the buildt-in hardware-SPI interface of the ATMega, which is defined...

Hello

The next questions is:
Must i remove the 1k and 22k resistors from the circuit, i mean direct connecting the two processors?

Thanks

regards
Pedro

Hello All

In my programm i not use the MAX232 inverter for serial communication to the PC, i use a 1k for tx and 22k resistor for rx Pic pin and the code like this

bmode con 16780' ...

Thanks you very much Darrel

Regards

Pedro