Thanks for posting your work Roger.
I've been wanting to experiment with a temp/RH device lately and this is enough to make it happen.
Copied to a file before it gets lost.
Type: Posts; User: LinkMTech; Keyword(s):
Thanks for posting your work Roger.
I've been wanting to experiment with a temp/RH device lately and this is enough to make it happen.
Copied to a file before it gets lost.
Merry Christmas Dave
Been awhile since I been here and found this post while trying to bring the same module to life.
After a lot of reading and comparing "working" code not in PBP, I found that a lot of confusion...
Anyone else experiencing USB CDC driver problems since Windows 10 went Anniversary on us?
In my case, it affected a Panasonic CF-31, 64-bit Intel core i7-5600U reporting "Driver not intended for...
I 4th the motion.
Congratulations! by the way.
You can only "see" so fast before it becomes a blur.
Try adding a PAUSE 33 in your main loop as it is, making it 30fps, just to test if the ghost dots go away.
Hi,
I would suggest writing to the LCD only when you need to update the display info.
Constantly writing to it in a loop without any kind of delay may be causing the problem.
pause 500
...
I could be wrong but I have to ask about using "CALL" instead of GOSUB for the sub routines CHECK and achizitie.
From the MCS Help section:
I've never used it in place of GOSUB so don't know...
Look into the PIC12F683.
I haven't used 2.50 in a long time but that's the PIC I started with.
I think a fixed Vdd to the PIC set below the "low battery" level is your only recourse with this one.
Then a simple voltage divider to monitor the battery level with the A/D to trigger sleep mode...
Hi abecker,
The inductors should be in your controller circuit because just as your intuition suggests, you will end up with a short antenna at the input of your box.
If you have room at the reed...
Like the guys said, a stiff pullup and a cap. I would also add an inductor to keep the noise spikes out.
You can probably get by without L2 in this diagram but added it in just in case.
8170
I noticed the variable "x" missing I hope will help.
for x = programStart to $1767F step 64
Flash = x
ERASECODE Flash
next x
I tried your INT code mod and sample code here (added Counter VAR Word) and it compiled okay.
A couple questions:
What are you try to do that is not happening?
And excuse my ignorance, but what is...
Edit: ooops, forgot the "@".
@ INT_ENABLE RABC_INT ; Enable IOC
I had to do the same thing with the PIC18F14K50.
Our entries look similar except your label is RABC_INT.
#define RAB_INT INTCON, RABIF ;-- RAB Port Change, Added 3/15/14 for PIC18F14K50...
It looks good to me. You need to check your connections and scope it and see if you're actually talking to it.
See post# 8 where the I2CREAD was used same as yours, just different address.
Noticed that Fujitsu also makes them too.
Web site
I'm spoiled to get them locally but check their site for regional sales locations here.
Check out the F-RAM. Cost more than the usual EEPROM but price has dropped by around half.
SPI or I2C interface devices, no write time delays and a trillion number of read/writes.
Used a PIC16F677 or a PIC16F685 in my devices.
PMs and PDF sent...
I didn't get to the RSSI function but didn't see it a problem since it means reading a register during the RX mode. The level range is pretty good and linear.
The RSSI value is available to be...
I use Express PCB and Pad2Pad for my boards.
Which kits did you order?
PM me your address so I can mail you some PCBs.
Steve,
I remembered unsuccessfully trying to solder rework wire to the module's pads only to damage it.
Do you make your PCBs?
I have some older revision PCBs with footprints for these module...
Yeah, I bought a pair of them MRF's too but only ended up staring at them cuz they look cool. :D