Thanks all for your advise
the at 389 the pressure is 3.3Bar but if its more than 3 bar i raise an alarm
my results are divided by 100 before its displayed.
Darrel the Lookup table works fine ....
Type: Posts; User: isaac; Keyword(s):
Thanks all for your advise
the at 389 the pressure is 3.3Bar but if its more than 3 bar i raise an alarm
my results are divided by 100 before its displayed.
Darrel the Lookup table works fine ....
Thanks for you help
i am work on this at the moment
but not sure its going to work out right
would test tomorrow
regards
Isaac
:._sour:Hello All
i have a big problem on my hands which i ned some help with.
i have got the following data which comes from a sensor and i need to calibrate this to Bar.
the sensor outputs...
Hello All
i am presently working on a project which has to send SMS msg when certain conditions are reached.
this works fine as you can see from the code here.
my question is "Is it possible to...
Found the problem
told you i was stupid
I2CWrite DS_SDA, DS_SCL, RTC, ContReg,[$20]
should be
I2CWrite DS_SDA, DS_SCL, RTC, ContReg,[%00000001]
Hello All
Just need a bit of help here .
I am trying to use the DS1337 as an alarm with INTA (pin 3 of Ds1337) connected to RB0 Interupt pin of my Pic
so that anytime the alarm time is reached...
Sorry Bruce
But got it going now
i meant it always displayed: start Measure on pc and no measurements but its ok now
thanks for you support
Isaac
Hi Bruce
i am trying to use your code on 18f452 but it seems to stop at start i must be missing something
DEFINE LOADER_USED 1 ' uses a bootloader
Include "Modedefs.Bas"
Define OSC 20
clear...
Bruce can this be applied to pic18f452?
I thought I get back to you ASAP as I have found out what the problem is
Its all to do with me using the original old Microcode Studio plus (The Black CD)
When I downloaded Microcode Studio Version...
Hello All
Does anyone know what the following assembler Errors are ?
i have being pulling my hair out since yesterday trying to complier my code but i get those errors
i am using pbp2.60 and MCS...
Thanks DT
much appreciated:wink-new:
Hello All
i am just trying to use the Debug command for the first time as i alway use the Hserout but
i need to save those pins for something else so i decided to use the Debug command on Port...
Hello Folks
Just a quick question as i am not sure this is possible.
i want to use the DS1307 and Ds1337 on the same I2C Bus to save myself two pins on the pic.
the problen is that both devices...
Not sure what you are trying to do but 0.7v is quite low
but if that's what you are measuring and assuming its the correct voltage why not fed it via an op amp then adc
I hope you get better as quick as possible i now get it clearly
i am waiting for delivery of Nano Lan Reach
http://www.connectone.com/media/upload/Nano_LAN_Reach_PB_01.pdf
but i am not clear as to if i use one of your shelds as below
...
Have you checked with a scope on the dc side if its fluctuating or stable?
Thanks pete
What Tellit module did you use
Isaac
Dave
Thank you very much for the link
it seems to be quite hard to get hold off in the uk but i have sent emails to both distribution listed for the uk
just keeping my finger grossed at the...
Thanks for your reply
i check that example out and i think that is what i am looking for
have anyone got any links of where to get them in the uk
Best Regards
Isaac
Hello Guys
i need your help is deciding which Serial to Ethernet module that is quite easy to use as there are quite a few out there when i do a search on both this forum and the internet.
This...
Hi Darrel
I have being reading your reply to this Bill ( Although its years old)
just wanted to know if there are now newer similar modules that are easy to use like those today.
i am thinking...
Hello All
i would be interested in hearing from anyone who has used a gsm module like Wavecom for Data Transfer.
I have successfully being able to send/receive SMS text from my remote data...
Thanks falingtrea
Thats what i thought as i knew the DG406 was not capable of supplying 100v
i just thought that there might had been a High Voltage version or similar
Isaac