Ok, I made a bit more progress, I changed "Define RESET_ORG 0x800" to "Define RESET_ORG 0x1000" and it now runs my program 'sometimes', its pretty random, after a reset sometimes it comes back up...
Type: Posts; User: Bonxy; Keyword(s):
Ok, I made a bit more progress, I changed "Define RESET_ORG 0x800" to "Define RESET_ORG 0x1000" and it now runs my program 'sometimes', its pretty random, after a reset sometimes it comes back up...
Henrik, the link only works for me if I right-click and select open in new window ?, very strange.
mister_e, ok thanks for that, I would never have found this package if you hadn't told me about...
Hi Henrik
That link is dead, whats a usb framework ?, I just need the bootloader firmware ?.
Nicmus
No I cant change the pulse widths and the lockout option is unavalable as well, so..
I think Im going to abandon the idea of counting pulses and try the totalizing method (as Jumper said), i...
Hi All
Stupid noob-type question for you...
I've never used a bootloader before and I now need to use the microchip usb bootloader with a 18f14k50, but Im damned if I can find it lol ???...
Hi Guys
aratti
I tried giving them odd numbers but with 6 coins if you write down all the possible coin combinations (which i did) you get diffrent coin combinations that add up to the same...
I have a vending machine that takes 6 diferent types of coin.
I can set my coin acceptor to give 1 to 50 pulses to my pic for any coin.
lets say I asign coin1 to give 1 pulse, coin2 gives 2...
Bruce, thank you :-)
Your code worked perfectly at 4 mhz first go :-)
So, I've hacked away at it all day and through trial & error and determination I have got it to work at 20mhz, It was a...
Bruce, thanks for uploading that code, I am going to try the code on my next day off work and will report back, I've had a look and its well commented and I can understand it, so I have fingers...
cncmachineguy
Yes I did, i still did not get valuses to match, I got values in the range of 552 to 614 and everything in between.
Thanks dhouston, but looking at more protocol descriptions is just giving me headache lol, I've been at it all week, I think I've actually looked at the description before when I was first googling...
I've looked at the nec ir protocol but i'm non the wiser :-(
Just if anyone is interested I have attached the actual code that came with my remote and reciver IC kit, it was written for the...
Thanks for your replies
Jumper, I dont have a schematic to post but Im using an easypic3 board with a 18f4550 at 5v with the tsop 2438 reciver on the same 5v with the output pin connected to...
Hi Guys
Ok, I am totaly stumpped with this, I have tried to use a timer as suggested by dhouston & I have been trying the pulsin method as suggested by bogdan but I get the same problem, the...
Hi Guys, thanks for sharing your code with me, dhouston i did see your code before when I was trawling the net and the forum for a solution, and bogdan I like your lookup table for the Ir data, but I...
Hi Guys & Gals
I'm going nuts
I am trying to decode the NEC remote protocol and I've been at it for days, I cant even measure the 9ms start pulse!
I have tried to use the pulsin command...
I was just reading some of the opinions and chatter about this subject and wondered to myself if this might be a better idea...
instead of asking people if they like it (because everyone will...
I gave the chat a go a few days ago, and I watched it for about half an hour and it never changed, it was just refreshing, I think no one is using it.
Would it be possible to have a one to one...
Ok, it is now working :-), the config from darrel's code above works, the problem was something to do with my PC, when I turned it on this morning and plugged im my 14k50 it enumerated straight away,...
Hi, I am going to check the vusb voltage today, the 18f14k50 / 13k50 is the cheapest usb part ?.
Hi, yes, I just noticed that, ok I copied that config into the program and also into the INC file and still device unrecognized :-(
Hi yeah dial-up can be a pain.
I used the prototype area on the lab-x1 for the 14k50, I tried darrels code and it gives the same problem but darrels code does not tell you what config settings to...
Thanks for sharing that config, I tried it but it does not work, I still get the device not recognized message, any ideas ?
Hi all, can anyone check my config in the picture below..
I am trying to get a 18f14k50 usb to work but I just keep getting the 'USB Device not recognized' message from windows.
I'm using a...
I bet you have seen the eeVblog thing where the OZ engineer slates the pickit 3 and Microchip makes a video response, quite entertaining I thought.. :)
...