Search Results - MEL PICBASIC Forum


Search:

Type: Posts; User: Dave; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    21
    Views
    480

    Re: Tiny bootloader and pbp

    Sheldon, Here is the source directory I use here. The forum does not allow files bigger than 1M so I can't send you the x0.11.2 executable.
  2. Replies
    21
    Views
    480

    Re: Tiny bootloader and pbp

    Sheldon, Where did you get the .ASM file for the processor? Looking at and comparing the two different files the one that you modified is rather old from 2016.01.15 revision 5 and the one I sent you...
  3. Replies
    21
    Views
    480

    Re: Tiny bootloader and pbp

    Sheldon, You don't have to compile it as the source ia already an .ASM file. It only needs to be assembled with MPLABX. That will give you an .HEX BootLoader file that needs to be FLASHED into the...
  4. Replies
    21
    Views
    480

    Re: Tiny bootloader and pbp

    Sheldon, Just modify this file extension from .txt to .asm. Then modify for the frequency and chip config and then assemble with MPLABX to get the .hex file for flashing. Then use TinyMultiBootLoader.
  5. Replies
    7
    Views
    311

    Re: Setting 8Mhz clock speed on PIC16F684

    Yes, That is correct. The PAUSE command is based on the OSC frequency. If you had an 4 Mhz. crystal connected and told PBP that the OSC was 8Mhz. the PAUSE command would give you 2 times the value...
  6. Thread: Minsky algorithm

    by Dave
    Replies
    3
    Views
    213

    Re: Minsky algorithm

    A rather interesting read Ioannis.
  7. Re: DT-Interrupts - Is there a clash between ExtInt and IntOnChange?

    Looking at your code I do not see the IRQ routine "ClockCount".
  8. Replies
    13
    Views
    1,628

    Re: Customizing the DT_INTS-XX.bas Instant Interrupt

    Glad to see you got it working Bo.
  9. Replies
    13
    Views
    1,628

    Re: Customizing the DT_INTS-XX.bas Instant Interrupt

    I din't see where you are clearing the individual IOCCF flag bits before or after the interrupt?
  10. Replies
    13
    Views
    1,628

    Re: Customizing the DT_INTS-XX.bas Instant Interrupt

    Bo, I have NO issue using it with IOC or INT. I would make sure ALL registers are set for using IOC. I have attached the page that tells of all the resisters affected.
  11. Replies
    13
    Views
    1,628

    Re: Customizing the DT_INTS-XX.bas Instant Interrupt

    Here is a modified version of DT_INTS_16 I changed to work with 16F18326 processors.
  12. Re: 16F887 - PORT pins interfere with each other when set high/low

    Hey CuriousOne, Where is the ENDIF to finish the "if BUTN=0 then" statement?
  13. Replies
    6
    Views
    446

    Re: Value of temperature

    I believe you are going wrong by not subtracting the zero degree C. offset before you calculated the final value of quanta. Here is what I calculate:

    0 degrees C. = 273.15 degrees K.
    273.15...
  14. Replies
    7
    Views
    369

    Re: Request : meCONFIG

    Lester, If you email me at "[email protected]" I can send back the .ZIP file you are requesting. This site does not allow more than 1 Mb file size. The .ZIP file is about 4957 Kb.
  15. Re: 18f4431 PORT.5 Problem Large automated machine

    I'm not sure the config strings are right. After looking at the .INC file in MPLABX it says the config bits are to be constructed such as:

    ;----- CONFIG1H Options...
  16. Re: Need to get 4 independently controllable frequency outputs, PBP can do that?

    Please,Please explain how you are going to get a single CD14536 to support 4 independent frequency's. I must be REAL stupid.....
  17. Re: Need to get 4 independently controllable frequency outputs, PBP can do that?

    4 separate PIC's with NCO modules. Done..... Why add unnecessary hardware?
  18. Thread: AD9833 Example

    by Dave
    Replies
    5
    Views
    1,310

    Re: AD9833 Example

    How are you going to do that with 1 AD9833?
  19. Thread: AD9833 Example

    by Dave
    Replies
    5
    Views
    1,310

    Re: AD9833 Example

    For those frequency's, Why not just use a PIC with an NCO module? No need for other hardware...
  20. Thread: 1936 ra.7 i/o ???

    by Dave
    Replies
    3
    Views
    302

    Re: 1936 ra.7 i/o ???

    Instead of using the PORTA.7 directive, why not use the LATA.7 directive? You maybe seeing the Read/Modify/Write problem. Try it....
  21. Replies
    3
    Views
    301

    Re: PIC10F320 not in devices list

    At version 3.1 it required an upgraded license. The last patches are free for the upgraded license. The current version is 3.1.3.4.
  22. Replies
    3
    Views
    507

    Re: Remote Control I/R TSOP4138 Help

    Andy, What do you mean by " is being spiked by mains EMI and causing issues."? Please explain... What is it doing wrong?
  23. Replies
    3
    Views
    507

    Re: Remote Control I/R TSOP4138 Help

    Andy, I would place a 10uF ceramic cap across the processor after the 100 Ohm resistor. I would also replace the 100 Ohm with a 10 Ohm. I have to ask what are you doing with the remaining pins on the...
  24. Re: Decoding variable into 4 digits of BCD, are there simple ways to this?

    Schematic...... Not some wild a** guess... Definitive schematic Please...
  25. Re: Decoding variable into 4 digits of BCD, are there simple ways to this?

    It all depends on how the hardware is configured. Is the design optimized for minimal code? With out a schematic it's hard to say...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4