Yes thank you
Type: Posts; User: l_gaminde; Keyword(s):
Yes thank you
I lost both computers settings got one working fine cannot get the shop to work keeps saying cannot find mpaswin I'm using PBP3 mplab 8.9 i think have run the config file that should set up...
It has been a long time since I’ve used that chip But I’m pretty sure you only need 3 pins It is a serial chip. And you may get by with using two of those pins But there will be no updating of the...
You were right on, took a look at my config and it was old style I did try to use manual config and it made no difference once I used #config it worked
thank you very much
ok I think i have the first problem fixed can compile my old programs but now I take an old program rename it and try to make a new project and get a warning red flag
Error[118] C:\0...
I received a notice that i needed to upgrade so i went to the link and updated and now none of my programs will compile I get this message
ERROR: Unable to execute mpasmwin.Skipping link step. ...
I can connect to a device using serialout2 at 9600 using 84 but how do I set the hserout to driven
what is the highest baud I can get using a 16f876a at 20mhz I would like 57600 what numbers would i use
I called Charles at Melabs it was a path problem all is well
hi Henrik
I'm using windows 7 home edition PB pro 2.60a and Mplab 8.53.
I'm thinking its a path problem but I have never used windows 7 so not sure how to set it and what to set, still using xp...
Im setting up PBP and MPLAB on an older laptop windows 7 home edition Im getting error ERROR: Unable to execute mpasmwin.Error[118] Im not sure where to start ?
OK after HenrikOlsson spanking I started checking from his line of thinking putting in a fast blink between steps and it was hanging at a serin command and not getting value into V! also found I was...
its an old program and not sure of the values, the value is correct from them but its in ascii rather than dec when outputed to lcd if I output to lcd dec3 v1 its fine I can put them on the screen...
I was just using that as an example to show I was getting ascii rather than dec, I have tried 50 and many other numbers along with = and => but without the dec modifier it just does not work guess I...
Below is code to make porta.5 led come on, the "If V1>100 then high porta.5" does not work. I have basically the same code where I send out 28 receive data in hex shift it and then display it on an...
do a Google search, there are three resistors that need to be done with wires in the pickit 3
does PBP work under mplabX
Ok been having problems with mplab v8.91 so started using 8.46 now there archived so do I use mplabx what is this and what verison do I look for.
will it work for pickit3 and XP any help is...
After a few days no problems
This is what i ended up doing installing v8.46 from a disk I had and after 15 programming tries it seams to program without errors voltage is still low out of the pickit3 and cannot be adjusted will...
Thanks Henrik and jerson maybe I have found the answer I have code protect on it has never acted this way before but once I turned it off it started working again. I have tried all your suggestions...
Well no that did not help it worked for about 4 times now back to the same cannot verify
Ok tried two different things hold chip in reset program and then verify works, also powering from external power supply works. guess its a USB port problem are there any good usb add in boards that...
Im using a pickit3 and it just started having problems it says it programs and verify but when you try to verify it says it 's not correct 16f876
Programming...
Programming/Verify complete
...
below is a serin2 statement that seems to start back at version rather than go to die is there something I'm missing
VERSION:
B = 1
GOSUB FLASH
PAUSE 500
B = 1
GOSUB FLASH...