I think you're right, i was reading it now and found out that this PIC is not suitable for oscillator or resonator, it should be used by either internal clock or external clock.
Thanks for your...
Type: Posts; User: Rony; Keyword(s):
I think you're right, i was reading it now and found out that this PIC is not suitable for oscillator or resonator, it should be used by either internal clock or external clock.
Thanks for your...
The other option is I/O function which is not the case, anyway i just tested it and didn't function.
8374
Resonator added to the schematic
8373
sorry i forget the resonator
I will put it now
83708371
Attached relative pictures
Hi everyone,
I got the PIC12F1572 and compile it with the PBP3.0.4.0
It runs properly when using INTRC, but with external oscillator it doesn't...
Although i set necessary configuration (ECH,...
Hi guys,
i need to run 3 PWM using the PIC16F1937, all at the same frequency.
I am trying at the first stage to use CCP1 and it is not working.
Below the registers i wrote:
APFCON =...
My version is PBP 2.50C
i am trying with serin2, the timeout is working properly,
but i faced another problem which is the [str varname\n]
serin2 IN_PIN,84,[str buffer\2] ' baud 9600
if buffer[0] = "A" and...
i think serin2 will work, i didn't pay attention for that before :(
thank you Steve :)
Hi all,
i want to read serial data using serin but the trame i am receiving is not always with the same size and it has not always the same bytes at the end (to wait for and stop reading).
i...
PORTB is internally puled up,
i switched ON pin 4 in the DIP switch (RB3 to zero) and still having the same problem :(
5748
With "DIP Switch"
5747
This is the PCB capture, thanks
Hi all,
I wrote a program using PBP250C for the 16F877A
i am using the ICSP to program the PIC, everything is working properly, i can write and read the PIC, but sometimes when trying to read...
Dear all,
i want to read a serial string buffer via the RX pin using Hserin, but the buffer is more than 255 bytes:
hserin 10,Label,[str buffer\1000]
is there a way to know when this...
i searched for the FCMEM, it is described as follows :
FCMEN: Fail-Safe Clock Monitor Enable bit
1 = Fail-Safe Clock Monitor enabled
0 = Fail-Safe Clock Monitor disabled
Now...
Finally i found it,
"gadelhas" remark lets me think about the configuration ... thank you :cool:
there is a check box called "FCMEM" in the WinPIC800 programmer, when turning it OFF, it works,...
i am using the following:
@ device pic16F767, hs_osc, wdt_off, pwrt_on, protect_on, mclr_off
lvp_off is not applicable with this PIC
=> same problem
i forget to say:
i changed the Oscillator, i tried with a resonator, i put a 100nF on the + and - very near to the PIC, i tried with 8MHz ... without sucess :confused: :confused:
i think it is not stoping, but it is going very very very slow.....
DEFINE OSC 20
PORTA = %00000000
PORTB = %00000000
PORTC = %00000000
TRISA = %10111111
TRISB = %00000000
TRISC = %10100010
Dear all,
i am facing a problem when using the PIC16F767: when i touch the oscillator pin and remove my finger, it stops running !! usualy when touching this pin the PIC stops runing (any other...
Hi Darrel,
i am facing another problem with the "CountBuffer = 50 - R4.HighByte".
when using the 16F877A, it works very well but since the program starts exceding 8K, i moved to 18F4620 (32K), in...
Thank you Darrel
it is working as i want.
Rony