Thank you very much Mark.
Type: Posts; User: Hebemabo; Keyword(s):
Thank you very much Mark.
Hello Henrik , its the code just before my reply. The one by deodeo.
I am programming a 12F683 using PBPro , Microcode Studio , MPASM and Pickit2.
I have selected 12F683 in MicrocodeStudio.
Hi,
I copied the program into Microcode Studio and when I compile it I get
the following errors:
ERROR: Variable wsave3 position request 416 beyond RAM_END 191.
ERROR: Variable wsave2 position...
Thank you very much Richard , your advice fixed my problem.
I am so happy 'cause I really like this chip.
Now I can apply my mind to getting an interrupt every minute which
appears to be quite...
PIC16F628, Pic Basic Pro 2.60, Pickit programmer
Good day ,
Below is my code to read the PCF8563:
I2Cread SDA,SCL,rtcadd,rtcloc,[secs,minu,hrs,DoM,doW,mon,year]
gosub waita ...
Thank you Henrik, I have now removed the config statements from the PBP 2.6 18F1220.inc file
and inserted the required config statements into my program. Works like a dream and no more
interfering...
Hi Richard , It's blinking now. I changed the config settings in the .inc file that exists in the
PBP 2.6 folder and I have no config statements in my source program.
Thank you very much for...
Hi Richard , thank you for your patience.
I tried all the changes you suggested but could not get it to work. I reverted back to PBP 2.6 and downloaded
MPLAB 8.9 which contains MPASM v5.5. I now...
Hi, I have now installed MPLABX , PBP3 and MCSX. Now I get [ASM ERROR] 18F1220 NOVA BX.ASM (30) : Symbol not previously defined (_INTIO2_OSC_1H) .
I've tried a lot of permutations and found that...
Hi Richard, my P18F1220.inc does not look anything like that.
I tried your config suggestion with slight mod ( see below) but it still does not work. I also tried with a copy of the .inc from...
Hi Richard, I'm using PBP 2.6. Not sure if my MPASM shipped with it.
Thank you
Hebe
Thank you Louie, I changed to LATA.1 then got a syntax error due to incorrect port use which I fixed. Now I get eleven lines of "error [177].......__CONFIG directives cannot be used with CONFIG...
Hi All, I am trying to convert a 16F88 program to run on a 18F1220. For starters I tried the attached blink LED program but can't get it to work.
I'm using Pickit2, Microcode Studio and MPASM ver....
This I use and it works well:
Start:
OWOUT DQ, 1, [ $33 ] 'send read Rom command
OWIN DQ, 2, [ FaM,skip 7] 'read sensor family code, skip ID and CRC
...
Hi Darrel , thanks again. I used your DIV32 remainder tip to do the rounding to 1mm.
I still have enough flash for my refinements
circ = puls * 1000
circ = (DIV32 fctr)
@ MOVE?WW R2,...
Hi Darrel , I looked through the PBP manual to get clarity on the "+R2.15" in the code you sent me but I could not find it. I presume that R2.15 means register 2 bit 15 and that it must be used...
Hi Darrel , thank you very much. It works like a dream and I've saved 263 words.
Hebe
Hi All , this is my first post. Any ideas?
I have written the following code in my program for a 16F88. It works but I need to free up some memory for other routines. Is there a more efficient...