thanks for the response,
I had on my mund a shift register that will receive the serial stream from the PIC and I did associated the scope display to the shift register...
I was in error when I...
Type: Posts; User: iw2fvo; Keyword(s):
thanks for the response,
I had on my mund a shift register that will receive the serial stream from the PIC and I did associated the scope display to the shift register...
I was in error when I...
iT IS MY FAULT:
Richard explanation is correct as usual !
Thanks for all.
All the best
regards,
Bye
Hi Peter,
could you please clarify better ?
( my English is not a first language )
Thanks
could you please check in the real situation:
connect the PIC DATA output to scope ch_1
connect the PIC clock output to scope ch_2 and set the trigger to this channel.
Tranmit bin 00000011 ( dec...
sorry: I did not tell that I am talking about the PIC output .
Thanks
thanks again,
I am sorry for not understand...
If I slow down the scope time base the dot goes from left to right.
So the first bit transmitted by the PIC is always to the right of the scope and...
the first bit sent out by the pic should be on the right ( 9 seconds old )
The last bit sent by the pic should be on the left ( 0 seconds old )
I am sorry for not understanding...
thanks
I am so sorry Richard:
if the time flows from left to right, then the first bit sent should be on the right and not to the left of the scope !
Where am I wrong please ?
Bye
thanks a lot,
Is your SPI device set to receive MSBfirst or LSBfirst please ?
Bye
good day to all in this forum,
I am using PicBasic pro to load an 8 bit shift register and I wrote a very simple program like this:
INCLUDE "MODEDEFS.BAS"
DT var byte
DT=128 ' decimal...
Thanks Henrik;
I am sorry for the PIC type: it is a PIC18F452.
I understand that I must read the low byte first and then read the high byte.
I must write the high byte first and then write the...
good day to all in this forum,
I am using pic18f877 as a counter and I would like to use timer0 in 16 bit mode for reading an external signal.
At the moment I am not able to read the whole 16 bit...
the procedure is to send the conf register and wait for the end of conversion bit and read the data : is this OK?
Ambro
so the trigger in triggered mode is the sending of the config register ?
Amb
Thanks,
it is somewhat clear to me now . I will follow that inmplementation.
> "set the config to the triggered mode you desire " : Yes, it is OK , but when does the trigger start pls ?
Amb
thanks,
let me try to explain....
The correction is applied every 150 msec.
let me say that at t=0 the correction is applied.
At t+50 msec the power supply output is completely set.
1> Should...
Thanks a lot Richard for the reply.
I will try to indicate what I am trying to implement .... using my limited English language.
My program applies a correction to a dc power supply by changing...
good day to everybody on this forum,
I am using INA219 sensor with PICbasic and it is working well as far as the data accuracy is concerned.
I do have a point to discuss regarding the configuration...
Thanks for your message: I hope to see some reference code.
Bye
Gooday to all of you in this forum,
I am using a PIC18 micro and I have to control the E32 rx/tx module in order to send and receive data.
I did read that the module operate through the UART (...
Thanks very much for all the suggestions received.
I did solve the problem by checking the pin state before launch SERIN2: it is working now.
All the best to all of you,
regards
Thanks Richard,
I am going to try to consider all the possible failures of the radio receiver.
Do you mean to use the HW UART pin RC7 ?
The point is that i am using two UART in this project.
Any...
good day to all in this forum,
I am currently using PIC18f252 for receiving a data stream via UART connected to portc.6 .
I use the following method: SERIN2 RX_12,396,3000,WARNE ,[WAIT("T="),STR...
Thanks to everybody for the assistance and for the sample code.
It is working very well now.
regards
Ambro
Hi to all in this forum,
I have to interface 40466 (40 chars X 4 lines) LCD with my PIC.
Is there any pic basic program to take as example please ?
Thanks for any help .
regards,
Ambro