Search Results - MEL PICBASIC Forum


Search:

Type: Posts; User: Szczepaniec; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    22,097

    Finding digital signals

    Is there a really easy to use method to see if there is some type of digital communications being passed through a wire? I am looking for something I can hand to another person with 2 minutes of...
  2. Re: Can't get the simplest of programs to run using internal osc and just toggling a

    I found an issue and correcting it seems to correct the issue. However, I am left a little confused as to what is going on. I am using MC Studio 5.0.0.5 with Melabs programmer v4.51 on a computer...
  3. Re: Can't get the simplest of programs to run using internal osc and just toggling a

    No dice. I have tried yet another PIC to make sure I didn't damage the last two and tried a different programmer in the event that was damaged (1 in a million, I know). My gut is that I am missing...
  4. Re: Can't get the simplest of programs to run using internal osc and just toggling a

    No, it didn't. Nothing was out of the ordinary as far as I could tell. It didn't before I added the alldigital file to the folder but I did it anyway just in case. I am completely baffled.
  5. Re: Can't get the simplest of programs to run using internal osc and just toggling a

    I have tried doing gpio.0 as well with no better result. This cut and paste is just the latest thing I have tried out of desperation. Not that it is right but I have numerous other programs that I...
  6. Re: Can't get the simplest of programs to run using internal osc and just toggling a

    Sorry. I should have put the PIC in. It is a 12HV615. I have Darrel's ALLDIGITAL file in the same folder as the project folder and everything compiles and acts normally. I have also tried more than...
  7. Can't get the simplest of programs to run using internal osc and just toggling a pin

    Here is the code. It will not toggle the pin. I have to be missing something painfully obvious. I am hoping somebody will spot it immediately and while making me feel dumb, save me another 17 days of...
  8. Replies
    2
    Views
    2,059

    Re: Using WPU and ADC

    I am using an OSRAM, SFH 300 FA-3/4 which works fine. It is apparently a problem with my code because it doesn't work on my breadboard but a more basic program utilizing the WPU, ADC, and an LCD...
  9. Replies
    2
    Views
    2,059

    Using WPU and ADC

    I have a piece of code I am having issues with and suspect it may have to do with the ADC and WPUs I am using. I am using a phototransistor to ground and attempting to read a relative value with an...
  10. Re: Code for reading a barometric sensor with PIC16F1827

    Thank you for the response. Charles from Windblown Solutions has provided me with a solution.
  11. Code for reading a barometric sensor with PIC16F1827

    I do not have the time nor the desire to learn how to work I2C communications with PICs. I am sure it is really easy but all the examples I am looking at are just making my head spin. I need code...
  12. Program Configuration check mark issue... maybe.

    I just spent a day and a half wondering what I did to my code to make it not work. Nothing made sense, things didn't work, and generally everything was a mess. After pulling back and reading PICS...
  13. Re: PIC18F2525 Port C pins made output causes problems in other circuits

    The system does run on batteries. That doesn't mean there aren't other sources of noise on the board but during troubleshooting I reduced or removed all of them to the maximum extent possible. I...
  14. Re: PIC18F2525 Port C pins made output causes problems in other circuits

    I just typed for 15 minutes explaining everything and pressed "Reply to Thread" instead of the button on the bottom "Post Quick Reply" which wiped out everything I typed. This might be something...
  15. Re: PIC18F2525 Port C pins made output causes problems in other circuits

    I just found the issue. It is a mystery why this PIC was affecting the LCD but it appears the display is very sensitive to BOR. If the ground is switched off and back on within 15 seconds or so the...
  16. Re: PIC18F2525 Port C pins made output causes problems in other circuits

    The other PIC does run the LCD but displays everything just fine until this PIC is plugged in. It also displays fine if plug the PIC in but comment out the setting of the TRIS registers for those...
  17. PIC18F2525 Port C pins made output causes problems in other circuits

    I have been grabbing for straws for about 20 hours on this. I have two 18F2525s working together and using 4 lines of DIO to do signal a few different states between the two. The issue I have boils...
  18. Replies
    0
    Views
    2,379

    2-3 week contract job

    I have a need for somebody that knows more than I (should be most people reading this forum) to do some PIC programming and some board layouts for me. It is on site in Denton TX so that the persons...
  19. Replies
    5
    Views
    3,046

    Re: ECIO with a PIC18F2525

    I guess I will join the crowd that doesn't trust the programmer menu. I wonder how many other projects I have scrapped in frustration over the same or similar issue?
  20. Replies
    5
    Views
    3,046

    Re: ECIO with a PIC18F2525

    It worked. Thank you very much.

    Why didn't it work when I selected that choice in the programmer menu?
  21. Replies
    5
    Views
    3,046

    ECIO with a PIC18F2525

    I am having an issue with a project running an 18F2525. It is my understanding that when I choose ECIO for the OSC in the meProg configuration that the PIC should be taking the clock signal in on...
  22. Replies
    2
    Views
    2,761

    Re: Commands for serial LCD

    Thank you for the help. The issue was with me doing something I should have known not to do. I was using the internal osc at 8 Mhz to run it. I switched to and EC and everything is fine. I...
  23. Replies
    2
    Views
    2,761

    Commands for serial LCD

    This seems like the most basic of problems and it is probably just the frustration of trying it for hours that is keeping me from the obvious answer. I have a New Haven Display Serial LCD 20x4...
  24. 5 day class in Florida to tutor PicBasic students

    I need a person with PIC Basic experience to tutor students learning PIC Basic Pro from 10-14 October. Local to Fort Walton Beech is preferred but we will cover travel expenses if you are located...
  25. Replies
    15
    Views
    9,512

    Re: Not getting the full output from pins

    Unsolved is relative to my world. Until it makes sense in my pea brain, it is unsolved. However, it is solved now.

    Thanks for all the help. I was unaware of the graphs posted here and when I...
Results 1 to 25 of 42
Page 1 of 2 1 2