I am working on one Battery Operated RF project with NRF24L01+ modules.
I need to arrange as much as low current consumption for both side as TX and RX. I have no problem on TX side because I can...
Type: Posts; User: ero; Keyword(s):
I am working on one Battery Operated RF project with NRF24L01+ modules.
I need to arrange as much as low current consumption for both side as TX and RX. I have no problem on TX side because I can...
It seems that the site is not exist anymore after darrel is died.
Is there anybody to put the necessary files including the samples to somewhere?
Ero
Max Power,
I need to make a correction. 12F675 having 10 bit ADC channels but I was using them as 8 bit. Because in that job I do not need 10 bit conversation.
I made a system which is working...
If your encoder is working with 5V , you can connect it direct to any port. But pls. remember you have to connect only the A and B outputs of that encoder. Of course if you want to check also the...
Thank you for the reply. I will do them.
Ero
I would like to use one touch button (or pad) with pic and I read the pdf file of Microchip AN1298 about that matter.
The document gives the following instructions to do the job;
* 1. Set 2nd...
Is there any default timeout period for Heserin command if I do not give any timeout figure and Label.?
One friend told me that "if you donot use the timeout in the command the program never leave...
Dear Majoka,
Normally I do not make a lot of calculation in that cases. I use simulator (isis) and I change the resistance value until I find the right output. If you need to make the calculation...
I do not remember what was in the file but I collected some of similar files which I had worked before . Pls. check the file in following link. I hope it helps you.
Ero
...
@Roberto,
I could not yet received your reply!. Is there any problem?.
Erol
@Roberto,
I checked now the datasheet of Motorola 145026. I can tell you the idea is absolutely same. There are some differences like followings;
- the pilot period is 18 clocks in motorola, (36...
Dear Friends,
I was planning to write a basic program for decoding the HT6012 signals by using pic 16F877. As you have understood the some part of the program can be written in Basic but the...
@rytech,
I have made similar system by using a pic. I explain you how it can be done.
The components;
1 pce. LM358 opamp
2 pcs. res. 1K 1/8 watt
1 pce res. 0R1 (0,1 Ohm) 5 watt or bigger.
1...
It does not work. I had made a lot of trial work before. There is only one way which is -txx$ if you give the pic number by this command you can get the pic. For instance to have the pic 16F877 you...
Very good. It is really interesting but I am sure there was something wrong first time. Anyhow, the important thing is the system is working now.
ERO
@Kamikaze47,
I do not know why it is not loading the hex file. I remember Long time ago it was happend to me also but really I do not remember how to solve that problem.
IT will be better to...
@Kamikaze47,
Pls. do the following instructions;
- RUN MCS
- Open the "View" pull down menu and select "Compile and Programmer Options"
- Push the "Programmer" button
- Push "Add New...
Steve,
Yesterday evening, I tested all the possibilities again after I made a new program which is only one loop. It was checking the button first after it was passing to SERIN2 command and...
Dear Steve,
Thank you for the tricks. You right I checked the program again and I saw that there are a lot of cunfusions. It was working but as you have said the reason can be the stack due to that...
@Mister_e,
I give you here the code. It is changed a lot of time but it is the last one which I used and by this program button is working a little bit for instance after 1-2 minutes it is making...
@Mister_e,
Yesterday, I made a lot of try in order to find a way for using the button. I have to tell you the result is still neagtive.
First of all I used Tiemout and label and tried from 1 ms...
@miter_e,
Thank you for the reply. I was thinking that something was making busy the port and everything is clear now.
I will try your suggestions.
Thanks again
ERO
Dear Friends,
Is there anybody can explain me why Serin2 and Button command do not work together?.
I write a simple program just receive some bytes from another pic and same program was...
Dear PICtron,
I have not yet used the Count command and I do not know how to use it. Could you pls explain how ?.
Auto range is only one idea. As a simple explanation you take about 1 ms....
@steve,
Lets make a simple calculation;
- The osc frequency is 10.000.000 Hz.
- The pic working frequency is 10.000.000/4 = 2.500.000 Hz.
- The period of one command cycle is :...