How can I find out which machines my PBP3 is registers on? Regards Graham Guthrie
Type: Posts; User: grahamg; Keyword(s):
How can I find out which machines my PBP3 is registers on? Regards Graham Guthrie
I am slowly progressing but have now getting a message that says HIGHJACKED_LCDOUT not found PBPPIC??.LIB.
Can you please advise on how to install this in the correct Library.
Thank, you Graham...
I am now trying to compile on an old Xp laptop machine and am getting the following message: Warning: unable to open INCLUDE file c:\libraries\documents\pbp projects\newexclusion\lcd_anypin.pbp....
I have installed pbp 3 on a Windows 7 machine and have registered with correct serial number. When I compile the asm file using microchip mpasm tool suite it compiles correctly. If I try to use the...
ppr=pulses per rotation.
Yes your formatting looks good.
Firstly ADCON1=%11100011 'JUSTIFY statement is conflicting with DEFINE ADC_CLOCK 3.
Secondly IF VOLTAGE=>1023 THEN statement can never be greater than 1023. DEFINE ADC_BITS 10 means maximum...
I have installed 3.0.8 and it works fine with mplab 8.92.
Will version 3.0.8 still work with mplab 8.92
I think you may wat to try the following: if (vala >650) and (vala <920) then go sub xx
Dave with a 47k resistor the current at 12 volts is only about 255 Micro amps. I have used this method hundreds of times and never had any problems. The input resistor can be as high as 270K and stil...
Why do you not just use a 47k resistor in series with the input pin. The internal diodes in the pic will clamp the input voltage anyway. No need for zeners or voltage dividers.
Thank you all, if have managed to deactivate and reactivate on new machine.
How do I remove pbp3 from an xp machine and reinstall an a windows 7 machine?
I have installed on a new windows 7 machine but it installs as a trial version. how do i get licence transfered to new...
Bob, please post your code so that we can see what you are trying to do.
PROCESSOR p12f609
#include "p12f609.inc"
__CONFIG _MCLRE_OFF & _CP_OFF & _WDT_OFF & _XT_OSC
start:
BANKSEL ANSEL
CLRF ANSEL
MOVLW fDh
MOVWF TRISIO
The Define OSC 8 does not change the oscillator speed. I only tell the compiler the speed so that internal delays are calculated correctly. To change the internal oscillator speed the osccon register...
I am trying to get the CTMU touch controller working. I have 8 touch pads, KBD1,KBD2,KBD3,KBD4,SHIFT1,SHIFT2,UP,DOWN. Values and loaded into two variables called SWITCH and SHIFT. Everything works...
Keith, MPLAB 8.9 is still available and that supports all the present microprocessors.
ANSEL and CMCON are only required for a 12f675 that has analog input capability. A12f629 does not have analog inputs so these commands are not required for the 12f629.
The clear command is not...
Looking at the compiler include file for a 12f683 the CCPR1 VAR WORD EXT has already been included. I think you should be able to comment this line out.
Can you please tell me what the...
You do not need a seperate hardware timer for each led. A single timer would do the job.:smile: Adapt the following code to suit your needs.
#config
__CONFIG _CONFIG1, _LVP_OFF & _FCMEN_ON...
Trisc should be = %00000100
I think your problem may be caused by your oscillator frequency. When using the 16f887 what oscillator were you using? When using the usart frequency you should use a crystal oscillator for stable...
I think you may be in the incorrect forum. This forum has nothing to do with Matlab.