I had a problem with adding PBP3 to a new computer, so I wanted to use the home site only to find it was trashed with baseball crap? Don't know anything more than this other than it's been this way...
Type: Posts; User: fowardbias; Keyword(s):
I had a problem with adding PBP3 to a new computer, so I wanted to use the home site only to find it was trashed with baseball crap? Don't know anything more than this other than it's been this way...
Did or does PBP3 have limited support for certain 24F devices? I remember a list of 24F devices that I thought was attached to the PBP3 device list? (not there now)
Here is the latest business model from Microchip Direct:
They had the chips I wanted in stock and at normal prices so I loaded them to the cart and was ready for checkout until the extortion card...
Conditions are still the same. I never did understand why our forums sites are not secure, or why any sight is not protected in todays environment . Just look at the recent posts that have trashed...
I cannot get to the Melabs main support forum because of a DNS ERROR 1001 involving Cloudflare? Is Leo and crew moving to Cloudflare and it is taking awhile to setup? I also cannot contact Melabs...
What is the practical length limit from a PIC to a LCD. If shielded cable were used would lengths of 15 to 20' be a problem. I have cables with individually shielded conductors plus an outer shield....
All issues are resolved. Site is available as usual. Didn't mean to make people upset. I was just concerned.
I had turn off web browser protection in the cable box to get there. The Comcast software flags out the site with a possible malware problem. That's all I know about this.
Site down for three days?. Hacking?, or is Melabs gradually disconnecting again to come back with big a surprise?
Yes I have attempted to change the configs from the list using the config commands in the program itself. Since the programming part fails this does nothing. I make try to use the PK3 with the...
I finally have the 16F19176 and the 18f47K42 invoking the programmer. I believe that issue was that I established my own file folder with all my programs in it and after the upgrade this path was...
Thank you for your reply. Yes, the fast program was in deselected. All I know at this time is that all of the older chips that I use are programming well. The issue is the 16F19176 which will not...
Recent upgrade to MeProg 4.64 and after a compile /program the programming window doesn't come up? I checked the MCSX compile and program window and it is showing the programmer. Tried various...
Good point. I found a few with 80,000hr. life expectancy (50% luminosity). OK for me, I'm going for it, cost around $30 US.
Has any one used the LCD write commands with a HD44780 "like" controller. Several OLED modules are advertised this way. How much "like" is my question? Did anyone find that the similarities were...
Thank you for the reply and I agree. I'll hold off on this. The reason is more of convenience. Some older project code is in assembly in the MPLAB IDE.
I recently up graded MPLABX to 4.15 and want to move the PB3 toolchain to the new IDE. Question: will I have a choice of programmers, PK3 or the PBP USB programmer? If a program with a pbp. extension...
Recent upgrade to PBP3 and it is running perfectly with another J-chip(18F26J53). Not so with the 18F67J94. Click program and get "Target device does't match.....)" Tried the usual things all OK. I...
No serial port was in use during programming writing. I would usually code a page and run test compile, and if good, add more lines. Sometimes I didn't use the thumb drive or any other connections...
I have had the MCS shutdown several times (gray-out) with a error screen. I believe this may have something to do with the file saving path. If I manually save my work every so often I have not...
Why do I see this when trying connect to the main support site.......http://support.melabs.com/?source=menubar.....Have bad people done some rotten things? If so, when will this flag clear or do we...
If PBP 2.6C is now static, the question I have is, how long will it be before the path(s) to the MPASM assembler located in MPLAB is lost due to Microchip upgrading the MPLAB or assembler? Also does...
I don't know if BASIC is dead, it does seem to take a back seat to C++ with the newer microcontroller development systems. I am more concerned about getting the 18F97J94 series added to the PB3...
Can anyone in the group confirm that the 18F97J94 will be added to the device list for PBP3 in the next upgrade? I will up grade when this PIC is added. The 18F97J94 was to be added last upgrade but...
Follow up on the 94 series: available from Microchip Direct for about $5. Regarding the adapters from Melabs, I would assume they are pinned out for the non V-bat devices, if so maybe the company...