Search:

the procedure is to send the conf register and wait for the end of conversion bit and read the data : is this OK?
Ambro

so the trigger in triggered mode is the sending of the config register ?
Amb

Thanks,
it is somewhat clear to me now . I will follow that inmplementation.

> "set the config to the triggered mode you desire " : Yes, it is OK , but when does the trigger start pls ?
Amb

thanks,
let me try to explain....

The correction is applied every 150 msec.
let me say that at t=0 the correction is applied.
At t+50 msec the power supply output is completely set.
1> Should...

Thanks a lot Richard for the reply.
I will try to indicate what I am trying to implement .... using my limited English language.
My program applies a correction to a dc power supply by changing...

good day to everybody on this forum,
I am using INA219 sensor with PICbasic and it is working well as far as the data accuracy is concerned.
I do have a point to discuss regarding the configuration...

Thanks for your message: I hope to see some reference code.
Bye

Gooday to all of you in this forum,

I am using a PIC18 micro and I have to control the E32 rx/tx module in order to send and receive data.
I did read that the module operate through the UART (...

Thanks very much for all the suggestions received.
I did solve the problem by checking the pin state before launch SERIN2: it is working now.
All the best to all of you,
regards

Thanks Richard,
I am going to try to consider all the possible failures of the radio receiver.
Do you mean to use the HW UART pin RC7 ?
The point is that i am using two UART in this project.
Any...

good day to all in this forum,
I am currently using PIC18f252 for receiving a data stream via UART connected to portc.6 .
I use the following method: SERIN2 RX_12,396,3000,WARNE ,[WAIT("T="),STR...

Thanks to everybody for the assistance and for the sample code.
It is working very well now.
regards
Ambro

Hi to all in this forum,

I have to interface 40466 (40 chars X 4 lines) LCD with my PIC.
Is there any pic basic program to take as example please ?
Thanks for any help .
regards,
Ambro

good day to all in this forum,

is there some implementation of PICBASIC code for controlling such a devices up to now ?

Thanks
Regards,

thanks,
I did register but not possible to get in due to error: could you pls specify the links again ?
Regards
Ambro

Good day Brice,
I used for years the program you have sent to me and it worked well sine I had the need to know the bus voltage only.
Now I am interested in getting the power and the current in...

good idea Sayzer,
thanks,
Ambrogio

good ,
it requires an external Nand gate but it is suggesting to use a resistor in series to the bs170 gate and another pic pin to turn on and off the carrier... this pin should be low state or...

thanks ,
but I am linked to the 18f1320 now.
Bye

Thanks,
at the moment my hardware consist of pic 18f1320, a tsal6100 emitter and tsop4038 receiver.
The emitter is driven by a bs170 mosfet and it handles about 200 mA of current.
I did transmit...

Good day to all in this forum,
I am trying to send serial UART data over the IR using rx and tx at 38 Khz with a baud rate of 1200.
Does anyone have any sample schematics and a sample code please ?...

thanks Richard,
Are you saying I have to remove the power to the PIC (target ) and supply it from the PICKIT only ?
I forgot to tell that if I connect a brand new pic12f675 everything goes well ......

I forgot to say that I have read and applied those instruction:

http://www.microchip.com/forums/tm.aspx?m=303686&mpage=2&key=&

Ambrogio

Thanks,
The three programming pins are connected to the PicKit only.
The 5vdc is applied to the PIC by the circuit : PICKit does no suuply power to Pic.
No way for now to recover them.
Bye ...

hi to all of you in this forum,
I programmed some 12f675 and 629 and I reassigned the pin that are normally used for programming the chips.
MCLR, PData and PClock do not have their function...